富士施乐C525A故障代码列表

http://www.oesell.com  来源:oesell.com  选稿:admin  文字大小:


富士施乐C525A故障代码列表
富士施乐C525A故障代码列表

故障代码

错误含义

具体描述

FIP/Corrective Action

Y Toner Life Warning

The yellow toner cartridge has reached the set toner supply time limit but it can still work.

FIP-1 75

M Toner Life Warning

The magenta toner cartridge has reached the set toner supply time limit but it can still work.

FIP-1 76

C Toner Life Warning

The cyan toner cartridge has reached the set toner supply time limit but it can still work.

FIP-1 77

K Toner Life Warning

The black toner cartridge has reached the set toner supply time limit but it can still work.

FIP-1 78

Toner Bottle Life Warning

The waste toner bottle is detected FULL by the SENSOR TNER FULL but can still work.

FIP-1 79


Xero CRU Life Warning

The drum has exceeded its specified rotation count but it can still work.

FIP-1 80

%s Check paper

IOT Paper Size Mismatch

Paper Size Mismatch detected.

Open/close the tray or remove and reload paper in Bypass Tray.

(No LCD Display)

Static Jam (Remain at OHP)

The SENSOR OHP was turned ON at Power ON or when the I/L was closed. (Static Jam)

FIP-1 39

001-358

IOT Fan Error Fuser

Fan Error Fuser detected.

Power OFF/ON

001-360

IOT Fan Error Rear

Fan Error Rear detected.

Power OFF/ON

003-356

NVRAM Error

An error occurred in the NVRAM on the PWBA MCU.

FIP-1 43

004-310

Communication Error Feeder

A communication error occurred between the PWBA MCU and the feeder.

FIP-1 40

004-311

Communication Error Duplex

A communication error occurred between the PWBA MCU and the Duplex.

FIP-1 41

004-321

TR0 Failure

The PWBA MCU did not receive the output signals from the SENSOR TR-0 (TR0 Sensor) at the specified timing.

FIP-1 44

004-324

Humidity Sensor Error

The inputs from the SENSOR HUM & TEMP are out of the specifications.

FIP-1 58

004-332

Deve Home Position Sensor Error

The PWBA MCU did not receive the output signals from the Rotary Home Position Sensor within  the specified time after the Rotary Developer had started rotation.

FIP-1 46

004-371

PAGE Timeout

The PAGEC/PAGE signal was not received within 60s after PFA had been sent.

FIP-1 42

006-370

ROS Motor Failure

The PWBA MCU did not receive the output signals from the SOS Sensor in the ROS within the  specified time.

FIP-1 45

007-340

Feed Motor Failure

The Feeder DRIVE ASSY FEED (Feed Motor) is not rotating at the specified speed.

FIP-1 59

007-341

Duplex Motor Failure

The Duplex MOTOR ASSY DUP (Lower Roll Motor) or MOTOR ASSY DUP INV (Upper Roll Motor) are not rotating at the specified speed.

FIP-1 60

009-340

ADC Contamination

An error occurred in the SENSOR ASSY ADC (ADC Sensor).

FIP-1 47

009-341

High Density

The output value from the SENSOR ASSY ADC (ADC Sensor) exceeds the specified value.

FIP-1 48

009-342

Low Density

The output value from the SENSOR ASSY ADC (ADC Sensor) is below the specified value.

FIP-1 49

009-343

IOT PCDC Error

PCDC error detected.

Power OFF/ON

009-344

High Coverage

The 500msec coverage for the lead edge of the image exceeds the limit.

FIP-1 51

009-358

BTR 2 Advance Error

The 2nd BTR Retract Sensor did not turn ON within the specified time.

FIP-1 53

009-359

BTR 2 Error

The inputs of the 2nd BTR Retract Sensor did not change during 2nd BTR initialization.

FIP-1 52

009-360

IBT CLN Fail

The SENSOR IBT RETRACT cannot detect Advance/Retract of the CAM ASSY-IBT CL.

FIP-1 61

009-361

Xero Verify Error

Data write error occurred in the ANTENNA ASSY (CRUM XERO).

FIP-1 7

009-362

C Toner Verify Error

Data write error occurred in the ANTENNA CTRG (CRUM CTRIG).

FIP-1 19

009-363

M Toner Verify Error

Data write error occurred in the ANTENNA CTRG (CRUM CTRIG).

FIP-1 15

009-364

Y Toner Verify Error

Data write error occurred in the ANTENNA CTRG (CRUM CTRIG).

FIP-1 11

009-365

K Toner Verify Error

Data write error occurred in the ANTENNA CTRG (CRUM CTRIG).

FIP-1 23

009-366

Xero Imitation Error

The drum cartridge with a different memory device has been installed.

FIP-1 8

009-366

Xero ID Error

The drum cartridge with different specifications has been installed.

FIP-1 9

009-367

C Toner Imitation Error

A cyan toner cartridge with a different memory device has been installed.

FIP-1 20

009-367

C Toner ID Error

A cyan toner cartridge with different specifications has been installed.

FIP-1 21

009-368

M Toner Imitation Error

A magenta toner cartridge with a different memory device has been installed.

FIP-1 16

009-368

M Toner ID Error

A magenta toner cartridge with different specifications has been installed.

FIP-1 17

009-369

Y Toner Imitation Error

A yellow toner cartridge with a different memory device has been installed.

FIP-1 12

009-369

Y Toner ID Error

A yellow toner cartridge with different specifications has been installed.

FIP-1 13

009-370

K Toner Imitation Error

A black toner cartridge with a different memory device has been installed.

FIP-1 24

009-370

K Toner ID Error

A black toner cartridge with different specifications has been installed.

FIP-1 25

009-371

IOT TONER ROTATE ERROR

Rotation error during toner replacement.

Cover is open.

009-390

Replace Toner K

NOT CONFIRMED

009-400

K developer life warning


009-402

Y developer life warning


009-403

M developer life warning


009-404


C developer life warning


009-405


2nd BTR life warning


010-317

IOT Fuser Detached

Fuser Detached detected.

Power OFF/ON

010-354

Temp Sensor Error

The SENSOR HUM & TEMP detected a temperature lower than -7 degrees Celsius or higher than 55 degrees Celsius.

FIP-1 55

010-397

Fuser Fail

The Control Thermistor detected a temperature higher than the specified value. The Safety Thermistor detected a temperature higher than the specified value. • The Control Thermistor does not detect READY within the specified time after the Main Lamp was turned ON during warm up. • The Main Lamp was still lit ON after the specified time had passed since the Control Thermistor had detected READY. • The Control Thermistor detected a temperature lower than the specified value after the specified time had passed since the Main Lamp turned ON during warm up. • The FUSER ASSY latch lever has not been installed properly.

FIP-1 54

010-400


Fuser life warning


016-300

ESS Data Cache Error

CPU data cache error.

FIP-1 82

016-301

ESS Instruction Cache Error

CPU instruction cache error.

FIP-1 82

016-302

ESS Illegal Exception

CPU invalid exception.

FIP-1 82

016-310

ESS FontROM Error (Main)

Built-in Font ROM check sum error.

FIP-1 82

016-311

ESS Font ROM Error (Option)

Option Font ROM check sum error.

FIP-1 82

016-312

ESS HD Failure

Detected by an HDD error.

FIP-1 82

016-313

ASIC Failure

TBD

FIP-1 82

016-314

Reserved (VSYNCerror)


FIP-1 82

016-315

ESS On Board RAM W/R Check Failure

Detected at Initial On Board RAM W/R Check.

FIP-1 82

016-316

ESS DIMM Slot RAM W/R Check Failure

Detected at Intial DIMM Slot RAM W/R Check.

FIP-1 82

016-317

ESS ROM Check(Main) Failure

Main Program ROM check sum error.

FIP-1 82

016-318

ESS DIMM Slot RAM Error

This occurs when an unavailable DIMM is inserted in the DIMM Slot during initialization process  at Power ON.

FIP-1 82

016-323

ESS NVRAM1 W/R Check Failure

Detected by Master NVRAM W/R Check

FIP-1 82

016-324

ESS NVRAM2 W/R Check Failure

Detected by Secondary NVRAM W/R Check

FIP-1 82

016-325

Reserved (for NVRAM3)


FIP-1 82

016-326

Reserved (for NVRAM4)


FIP-1 82

016-327

ESS NVRAM1 SIZE And ID Check Failure

Detected by matching check of the system required NVRAM size and the real size and of the ID to be recorded at the first Power ON.

FIP-1 82

016-328

Reserved (for NVRAM2)


FIP-1 82

016-330

NIC-ESS Communication Failure

Communication failure between the NIC and ESS.

FIP-1 82

016-331

NIC Flash ROM Boot Module Checksum Error

FIP-1 82

016-332

NIC RAM R/W Test Error FIP-1 82

FIP-1 82

016-333

NIC Flash ROM Application Module Checksum Error

FIP-1 82

016-334

NIC MAC Address Checksum Error

FIP-1 82

016-335

NIC Ethernet BIST parity/RAM R/W Error

FIP-1 82

016-336

NIC Internal Loop back Error

FIP-1 82

016-340

On Board Network Communication Failure

Communication failure between the 1 CPU network and the ESS F/W.

FIP-1 82

016-344

On Board Network MAC Address Checksum Error

FIP-1 82

016-345

On Board Network Ethernet BIST Parity/ RAM R/W Error

FIP-1 82

016-346

On Board Network Internal Loop back Error


FIP-1 82

016-350

IEEE1284 Data Error

Detected by the IEEE1284 controller.

FIP-1 82

016-351

Reserved


FIP-1 82

016-355

USB Error (Spec only for DIAG)


FIP-1 82

016-360

PCI Option#0 Fail

PCI option 0 detection error.

FIP-1 82

016-361

PCI Option#1 Fail

PCI option 1 detection error.

FIP-1 82

016-370

IOT-ESS Communication Failure

Communication failure between the IOT and ESS.

FIP-1 82

016-380

MACPHY CHIP TEST Error (Spec only for DIAG)


FIP-1 82

016-381

MACPHY INT LOOP TEST Error (Spec only for DIAG)

FIP-1 82

016-382

MACPHY EXT LOOP TEST Error (Spec only for DIAG)

FIP-1 82

016-383

DOWNLOAD ID ERROR

The download file ID is incorrect.

Press the Set button.

016-384

DOWNLOAD RANGE ERROR

The write destination address during download is incorrect. Range check error.

Press the Set button.

016-385

DOWNLOAD HEADER ERROR

The download file header information is incorrect.

Press the Set button.

016-386

DOWNLOAD CHECKSUM ERROR

The download file check sum is incorrect.

Press the Set button.

016-387

DOWNLOAD FORMAT ERROR


The download file format is incorrect.

016-388

DOWNLOAD INITIAL ERROR

IC activation in the download mode has failed when downloading the optional NIC.

ress the Set button.

016-389

OWNLOAD INSERTION ERROR

ownload was performed when the optional NIC was not installed.

ress the Set button.

016-390

OWNLOAD COMM ERROR

communication error occurred when downloading the optional NIC.

ress the Set button.

016-391

OWNLOAD PROTECT ERROR

W download was performed when FW update was prohibited by the panel settings.

Press the Set button.

016-392

DOWNLOAD DELETE ERROR

Flash deletion error during download.

FIP-1 82


 



网友相关回复如下:(以下网友回复只代表网友个人观点,不代表苏州办公耗材网观点)

昵称: 匿名
内容:
      


热门文章 20 篇
最新文章 20 篇