富士施乐1810出现错误004345,纸张设定左下方有感叹号
更新时间:2026/11/22 4:46:37,view:4429苏州施乐1810打印机售后服务中心客服热线69616769,苏州施乐打印机售后维修电话,施乐打印机售后网点,施乐1810富士s怎么看硒鼓打印了多少张,富士s复印机复印墨浓怎样调整,s故障061-321,富士S代码010311,s开机显示010-311,S设置旁路进纸,复印机鼓寿命清零,富士s废粉盒清理,s出纸口电机无反应,提示A5,s显示e-1,富士提示E3,出现010311如何解决,富士s一直显示没粉,复印打印底灰,1810维修视频2026/11/22
富士施乐1810 出现错误004345,纸张设定左下方有感叹号
技术交流平台 过眼云烟 2016-7-29 15:35:32
施乐s1810出现004345代码,纸张设定下方出现感叹号。望高手尽快解答啊。
技术交流平台 过眼云烟 2016-7-29 15:38:09
施乐s1810出现004345代码,纸张设定下方出现感叹号。望高手尽快解答啊。
技术交流平台 维修师傅 2016-7-30 7:20:39
纸张类型设置不正确,重新设定即可。
小马 2017-6-14 22:32:42
施乐复印机显示004一345代码
MCU/ HVPS通讯故障。解决方案:1、检查5 VDC从P/ J574-5至P/ J574-4对HVPS控制PWB2、 断开 P/ J574.Is有5 VDC从第j574-5到J574-43、检查电线从J411-5到J574-5的对地短路4、切断电源,并检查这些电线的断路或短路接地以下5、HVPS控制电路板P / J574-9到MCU板P / J411-16、HVPS控制电路板P / J574-8到MCU板P / J411-27、HVPS控制电路板P / J574-7到MCU板P / J411-38、HVPS控制电路板P / J574-6到MCU板P / J411-49、检查开路或P / J411之间的5 VDC电源线连接松动,针脚5和6;和P / J574,针脚5和410、如果这不能解决问题,请更换高压电源控制电路板和发动机控制板
004-345MCU/HVPS
Communication Fail.SOLUTION:Check 5 VDC from P/J 574-5 to P/J 574- 4 on the HVPS Control PWB 2.Disconnect P/J 574.Is there 5 VDC from J 574-5 to J 574-4 3.Check the wire from J411-5 to J574-5 for a short circuit to ground 4.Switch off the power and check these wires for an open or short circuit to ground for the following: 5.HVPS Control PWB P/J574-9 to MCU PWB P/J411-1 6.HVPS Control PWB P/J574-8 to MCU PWB P/J411-2 7.HVPS Control PWB P/J574-7 to MCU PWB P/J411-3 8.HVPS Control PWB P/J574-6 to MCU PWB P/J411-4 9.Check for open circuit or loose connections in the 5 VDC supply wires between P/J411, pins 5 and 6; and P/J574, pins 5 and 4. 10.If this does not resolve the problem, replace the HVPS Control PWB & Engine control Board

施乐s1810出现004345代码,纸张设定下方出现感叹号。望高手尽快解答啊。

施乐s1810出现004345代码,纸张设定下方出现感叹号。望高手尽快解答啊。

纸张类型设置不正确,重新设定即可。

施乐复印机显示004一345代码
MCU/ HVPS通讯故障。解决方案:1、检查5 VDC从P/ J574-5至P/ J574-4对HVPS控制PWB2、 断开 P/ J574.Is有5 VDC从第j574-5到J574-43、检查电线从J411-5到J574-5的对地短路4、切断电源,并检查这些电线的断路或短路接地以下5、HVPS控制电路板P / J574-9到MCU板P / J411-16、HVPS控制电路板P / J574-8到MCU板P / J411-27、HVPS控制电路板P / J574-7到MCU板P / J411-38、HVPS控制电路板P / J574-6到MCU板P / J411-49、检查开路或P / J411之间的5 VDC电源线连接松动,针脚5和6;和P / J574,针脚5和410、如果这不能解决问题,请更换高压电源控制电路板和发动机控制板
004-345MCU/HVPS
Communication Fail.SOLUTION:Check 5 VDC from P/J 574-5 to P/J 574- 4 on the HVPS Control PWB 2.Disconnect P/J 574.Is there 5 VDC from J 574-5 to J 574-4 3.Check the wire from J411-5 to J574-5 for a short circuit to ground 4.Switch off the power and check these wires for an open or short circuit to ground for the following: 5.HVPS Control PWB P/J574-9 to MCU PWB P/J411-1 6.HVPS Control PWB P/J574-8 to MCU PWB P/J411-2 7.HVPS Control PWB P/J574-7 to MCU PWB P/J411-3 8.HVPS Control PWB P/J574-6 to MCU PWB P/J411-4 9.Check for open circuit or loose connections in the 5 VDC supply wires between P/J411, pins 5 and 6; and P/J574, pins 5 and 4. 10.If this does not resolve the problem, replace the HVPS Control PWB & Engine control Board
热门图文资料