爱普生7621报错0x9A
更新时间：2024/4/22 10:19:18,view:361爱普生打印机7621苏州爱普生打印机售后维修服务中心电话0512-696l6769，苏州爱普生维修点电话, 爱普生l630k开机闪灯, epson551补充墨水, 爱普生l551扫描灯怎么修, EPSON L1300更换搓纸轮视频或者图解
, 爱普生615k2打印几下就亮三灯,
苏州爱普生报修电话696l6769,维修现场维修
error 0x9A. printhead error 打印头错误
Hard reset done no change, no paper in printer to jam it.
Unable to run adjustment program due to error.
checked the DC volts from the power supply seems ok although low (NOT SURE WHAT THE DC OUTPUT VOLTS SHOUD BE ON THE PS) when I check the volts at the CR motor terminals there is zero DC volts.
main board US due to ink flooding and shorting out say the print head
But in your case your printer seems to be failing the post boot, so there may be other related problems in there, like the logic board, it's hard to say..
Have you solved your problem with printer What was the reason Now I have the same issue - it happend after printing head cleaning.
most of the epson printers with the 0X9A problem all fail at about one year old and it does not matter if you use original OEM eposn ink or refills or CIS systems. Most of the time it's the black ink that leaks down, followed by the cyan.
If you catch the problem right away there is a good chance that you can recover the print head however after a couple blockages it's already too late.
I had the same issue: 0xE8 and later 0xEA codes. I could see that it was the white moving clip under the ink tank holder when on the far right that was catching it. The ONLY thing that fixed it was: once it made a noise and errored I unwillingly pushed the tank holder over to the left until the tanks pushed past the white clip and all the way to the left..
爱普生7621报错0x9A
技术 商祺电脑 发表于 2023/11/5 一是打印头感应器坏了。二是打印头坏了。二是主板上的F1或F2保险管烧了(此件很细小,正常很难发现)。 0 X 9 A 是主板电路故障， 也就是喷头42V供电没有了
error 0x9A. printhead error 打印头错误
Hard reset done no change, no paper in printer to jam it.
Unable to run adjustment program due to error.
checked the DC volts from the power supply seems ok although low (NOT SURE WHAT THE DC OUTPUT VOLTS SHOUD BE ON THE PS) when I check the volts at the CR motor terminals there is zero DC volts.
main board US due to ink flooding and shorting out say the print head
But in your case your printer seems to be failing the post boot, so there may be other related problems in there, like the logic board, it's hard to say..
Have you solved your problem with printer What was the reason Now I have the same issue - it happend after printing head cleaning.
most of the epson printers with the 0X9A problem all fail at about one year old and it does not matter if you use original OEM eposn ink or refills or CIS systems. Most of the time it's the black ink that leaks down, followed by the cyan.
If you catch the problem right away there is a good chance that you can recover the print head however after a couple blockages it's already too late.
I had the same issue: 0xE8 and later 0xEA codes. I could see that it was the white moving clip under the ink tank holder when on the far right that was catching it. The ONLY thing that fixed it was: once it made a noise and errored I unwillingly pushed the tank holder over to the left until the tanks pushed past the white clip and all the way to the left..
爱普生7621报错0x9A
热门图文