苏州维修电话696l6769,> 维修资料 > hp > 苏州HP DesignJet T790售后维修电话696l6769> 苏州hp打印机维修服务网

hp DesignJet T790常见故障代码描述,英文手册1

Code: 01.0:YZ
Description:
Communication with Engine PCA failed
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Remove the Formatter and reinsert it again. Ensure that it connects properly in the Engine PCA connector. • Replace the Engine PCA. • Replace the Formatter.
Code: 01.1:YZ
Description:
Error in the Engine PCA
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Engine PCA. 3. Replace the Formatter.
Code: 01.2:YZ
Description:
Failure communicating with an Ink Supply
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Perform the Ink Delivery System diagnostic test. – If the test finds that the ink supply is defective, replace it. – If the test does not find any errors, remove all the ink supplies from the ISS and reboot the product. 3. Install the ink cartridges with the product booted in normal mode. Use the replacement option available from the Touch Control Panel and install the cartridges one by one. If an error appears after installing a supply, the last supply you installed is defective. Replace it. 4. Check that the cables between the Left Ink Supply Station and the Engine PCA are not damaged and are correctly connected. In case of any damage replace the cables; see Connecting the Data Harness and ISS Harness Cable 5. Replace the Left Ink Supply Station. See Left Ink Supply Station. 6. Replace the Engine PCA. See EE Box.
Code: 02.1:YZ
Description:
Problem with the Carriage PCA
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Trailing Cable is not damaged. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA. 3. Replace the Carriage PCA. See Carriage PCA. 4. Replace the Trailing Cable and Carriage PCA Covers. 5. Replace the Engine PCA. See EE Box.
Code: 03.0:10
Description:
Battery of Real Time Clock ran down
Remedy:
Replace the battery.
Code: 03:YZ
Description:
Problem with Power Supply Unit
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Power Supply Unit (PSU). See Power Supply Unit
Code: 06:YZ
Description:
Failure reading/writing NVM in Hard disk
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Hard Disk.
Code: 07.01:11
Description:
DelSol3 ASIC not found or not responding
Remedy:
1. Check the condition and connections of the Interconnect data and power cable, replace if necessary

Code: 07.02:11
Description:
USB Cable not connected
Remedy:
1. Check the condition and connections of the USB cable, replace if necessary.
Code: 07.03:10
Description:
USB Hub not found
Remedy:
1. Make sure Interconnect board connector labeled 'INPUT HUB' is properly connected. 2. Make sure Wukong board connector labeled JUSB2 is properly connected to the cable coming from Interconnect board. 3. If failure continues, troubleshoot the error by changing the USB cable from Engine PCA to Interconnect, if the error follows to the changed part the USB cable is faulty, if it does not, the part is faulty. 4. Replace the Interconnect PCA, see Interconnect PCA. 5. Replace the Formatter Board see Formatter 6. Replace the Engine PCA
Code: 07.03:11
Description:
USB Scanner connected to incorrect port
Remedy:
Ensure that the USB cable from the Scanner to the Interconnect board is connected at the connection labeled 'SCANNER' and not 'HOST CON'
Code: 07:10
Description:
Interconnect Board or Power cable has failed
Remedy:
1. Check the condition and connections of the Power Cable, replace if necessary. 2. Replace the Interconnect Board
Code: 08:01:11
Description:
Touch Control Panel USB Cable fails
Remedy:
1. Check the condition and connections of the Touch Control Panel USB cable, replace if necessary. 2. If the error continues, replace the Touch Control Panel Touch Control Panel
Code: 08:04
Description:
Touch Control Panel communication to the product functions at the initialization, but during normal working the communication is lost.
Remedy:
1. Check the event log at the EWS support pages to see if there is another SE (for instance 07:10) and troubleshoot the problem more accurately.Appendix C: Obtaining the product log and the diagnostics package 2. Turn off the product and turn on again, and check to see if the error remains. 3. Upgrade the firmware For more information, see Appendix B: Emergency firmware upgrade with USB flash drive 4. Replace the HDD, see Hard Disk Drive 5. Escalate the issue.
Code: 08:08
Description:
A feature on the Touch Control Panel hangs or will not function (copy,scan etc)
Remedy:
1. Turn off the product and turn on again, and check to see if the error remains. 2. Upgrade the firmware For more information, see Appendix B: Emergency firmware upgrade with USB flash drive 3. Escalate the issue.
Code: 08:11
Description:
No communication between the product and the Touch Control Panel
Remedy:
1. Check the event log at the EWS support pages to see if there is another SE (for instance 07:10) and troubleshoot the problem more accurately.Appendix C: Obtaining the product log and the diagnostics package 2. Check the LED’s on the formatter to see if there is another issue and troubleshoot it more accurately. 3. Turn off the product and turn on again, and check to see if the error remains. 4. Upgrade the firmware 5. Check the condition of the USB cable, check it is not damaged or incorrectly connected. Reconnect USB cable (from Engine PCA to the Interconnect PCA or from Interconnect PCA to the Touch Control Panel 6. Replace the USB cable 7. Replace the Interconnect PCA, see Interconnect PCA. 8. Replace the Engine PCA see EE Box 9. If the error continues, replace the Touch Control Panel Touch Control Panel

Code: 09.01:10
Description:
Scanner Motor is failing
Remedy:
1. Perform the Scanner motor diagnostics. 2. Replace the Scanner Motor Scanner Motor Assembly (MFP only)
Code: 09.02:10
Description:
CIS A Element is failing
Remedy:
Replace CIS A Element CIS Element (MFP only)
Code: 09.03:10
Description:
CIS B Element is failing
Remedy:
Replace CIS B Element CIS Element (MFP only)
Code: 09.04:10
Description:
CIS C Element is failing
Remedy:
Replace CIS C Element CIS Element (MFP only)
Code: 09.05:10
Description:
CIS D Element is failing
Remedy:
Replace CIS D Element CIS Element (MFP only)
Code: 09.06:10
Description:
CIS E Element is failing
Remedy:
Replace CIS E Element CIS Element (MFP only)
Code: 09.08:11
Description:
Power cable of the Scanner is failing
Remedy:
Check the condition and connections of the Scanner Power cable, if necessary replace the cable.
Code: 09.09:11
Description:
USB cable of the Scanner is failing
Remedy:
Check the condition and connections of the Scanner USB cable, if necessary replace the cable.
Code: 09.10:04
Description:
Scanner is in SAFE MODE
Remedy:
Restart the product, if the problem persists replace the SCU. See Scanner Controller Board (MFP only).
Code: 09.10:10
Description:
Scanner SCU is failing
Remedy:
Replace the Scanner SCU.See Scanner Controller Board (MFP only).
Code: 09:01
Description:
Media jam in Scanner
Remedy:
1. Open the CIS to solve the media jam and close it again. 2. If no paper is seen, run Scanner Motor Diagnostic, refer to the Users Guide for further details.
Code: 09:02
Description:
Scanner not calibrated
Remedy:
Calibrate the Scanner
Code: 09:03
Description:
File I/O Error
Remedy:
Reboot Product
Code: 09:04
Description:
Contex Library failed to load
Remedy:
1. Reboot the Product 2. Upgrade the firmware For more information
Code: 11:YZ
Description:
Trailing Cable does not seem to be detected
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Trailing Cable is not damaged; replace it if necessary. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA. 3. Replace the Carriage PCA. See Carriage PCA. 4. Replace the Engine PCA. See EE Box.
Code: 21.1:YZ
Description:
Failure moving the Primer Motor of the Service Station
Remedy:
1. Remove the Right Cover and make sure the cables from the Engine PCA to the Service Station are connected and are not damaged. In case of any damage replace the affected cable; see Engine Cables Kit 2. Perform the Primer Motor diagnostic test (listed under the service station diagnostic test) to troubleshoot the problem further. See Primer motor. 3. Replace the Service Station. See Service Station.

Code: 21.2:YZ
Description:
Failure testing the length of the Service Station path
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product. 2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. 3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. It may happen that the cutter is blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage. 4. Perform the Service Station diagnostic test to troubleshoot the problem further. See Service Station Test. 5. Replace the Service Station. See Service Station.
Code: 21:YZ
Description:
Failure moving Service Station
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product. 2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. 3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. The cutter may be blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage. 4. Perform the Service Station diagnostic test to troubleshoot the problem further. See Service Station Test. 5. Replace the Service Station. See Service Station.
Code: 22.0:YZ
Description:
Left Ink Supply Station error, module 0.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable. 3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further. See Ink Delivery System (IDS) Test. 4. Replace the Left Ink Supply Station. See Left Ink Supply Station. 5. Replace the Engine PCA. See EE Box.
Code: 22.1:YZ
Description:
Left Ink Supply Station error, module 1
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable. NOTE: Check the Data Harness and ISS Harness Cable are connected in the right position onto the Engine PCA. These two connectors can be swapped by mistake causing a SE 22.1:10. Check the instructions in Connecting the Data Harness and ISS Harness Cable 3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further. See Ink Delivery System (IDS) Test. 4. Replace the Left Ink Supply Station. See Left Ink Supply Station. 5. Replace the Engine PCA. See Starwheel Assembly.
Code: 24:YZ
Description:
Ink Setup failure
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Insert the new purgers, reconnect the power cord and power on the product. 2. Perform the Ink Delivery System diagnostic test in order to check that the bongos (pushers) go up and down to pressurize ink in the tubes and the Out of Ink sensors work properly. See Ink Delivery System (IDS) Test. 3. Try purging the Ink Supply Tubes again once the product has been restarted. 4. If the diagnostic test does not find any problem, install new cartridges in the product and try purging the Ink Supply Tubes again. It could be that one of the cartridges is defective. 5. If the problem persists, replace the Ink Supply Tubes. You must bring purgers and ink cartridges. See Ink Supply Tubes & Trailing Cable.
Code: 26:01
Description:
Ink supply error found during IDS diagnostic test. In the Touch Control Panel message you will see letters representing the names of the colors of the faulty supplies.
Remedy:
1. Reseat the faulty ink supply and repeat the Ink Delivery System diagnostic test. 2. If the problem persists, replace the faulty ink supply and repeat the Ink Delivery System diagnostic test. 3. If the problem persists, replace the Left Ink Supply Station. See Left Ink Supply Station.
Code: 39.1:01
Description:
Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.
Remedy:
There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 1 in standby or resume operation.
Code: 39.2:01
Description:
Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.
Remedy:
There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 2 in standby or resume operation.

Code: 41:YZ
Description:
Electrical fault or current limit in Media-Axis Motor
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Media Advance Roller. If there is a wrinkled mass of paper inside the paper path, lift the Pinch wheels (using Media Lever) and clear the obstruction. 3. Perform the Paper Drive diagnostic test to troubleshoot the problem furthe. See Paper Drive Test. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Check that the Media Advance Drive cable is not damaged and is correctly connected to the Engine PCA. 6. Replace the Media Advance Drive. See Media Advance Drive. 7. Replace the Engine PCA. See EE Box.
Code: 42:YZ
Description:
Electrical problem (fault, current limit, overheating) in Scan-Axis Motor
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Carriage Assembly. Remove any obstacle to let the carriage move freely along the whole scan axis. If there is a wrinkled mass of paper inside the paper path, raise the pinch wheels (using the Media Lever) and clear the obstruction. 3. Check that the Scan-Axis Motor cable is not damaged and is correctly connected to the Engine PCA. 4. Replace the Scan-Axis Motor. See Scan-axis Motor. 5. Replace the Engine PCA. See EE Box.
Code: 45.1:YZ
Description:
An error with the Rewinder 1 System (Upper Rewinder) has been detected.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Remove the paper from Roll 1. Reconnect the power cord and power on the product. 2. Check that the Rewinder 1 cable is not damaged and is correctly connected to the Engine PCA. 3. Check that the Upper Right Roll Support is correctly attached to and aligned with the Right Cover. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Replace the Upper Right Roll Support. See Roll Support, Upper Right.
Code: 45.2:YZ
Description:
An error with the Rewinder 2 System (Lower Rewinder) has been detected .
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Remove the paper from Roll 2. Reconnect the power cord and power on the product. 2. Check that the Rewinder 2 cable is not damaged and is correctly connected to the Engine PCA. 3. Check that the Lower Right Roll Support is correctly attached to and aligned with the Right Cover. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Replace the Lower Right Roll Support. See Roll Support, Lower Right.
Code: 47:YZ
Description:
Starwheels motor error
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Starwheel Assembly, then clear the obstruction. 3. Check that the Starwheel Assembly cable is not damaged and is correctly connected to the Engine PCA. 4. Perform the Scan Axis Starwheel diagnostic test to troubleshoot the problem further. 5. Replace the Starwheel Motor. See Starwheel Motor. 6. Replace the Engine PCA. See EE Box.
Code: 48:YZ
Description:
PPS system failure
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Pen to Paper Space (PPS) Solenoid cable is not damaged and is correctly connected to the Engine PCA. 3. Perform the Scan Axis PRS diagnostic test to troubleshoot the problem further. 4. Replace the Pen to Paper Space (PPS) Solenoid. See Pen to Paper Space (PPS) Solenoid. 5. Replace the Engine PCA. See EE Box.
Code: 51:YZ
Description:
Scanner Position Sensor failure
Remedy:
1. Check that the Scanner Position Sensor cable is not damaged and is correctly connected to the Engine PCA. 2. Perform the Sensors Test to troubleshoot the problem further. See Sensors Test. 3. Replace the Scanner Position Sensor. See Scanner Position Sensor (MFP only).
Code: 52:10
Description:
The product has detected a failure in the Drop Detector.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Drop Detector cable is not damaged and is correctly connected to the Engine PCA. 3. Replace the Drop Detector. See Drop Detector. 4. Replace the Engine PCA. See EE Box.

热门图文

相关资料补充


热门关注
· hp designjet t790常见故障代码描述,英文手册

· hp designjet t920 eprinter常见故障代码描述,英文手册2

· hp designjet t920 eprinter常见故障代码描述,英文手册1

· hp designjet t930常见故障代码描述,英文手册2

· hp designjet t930常见故障代码描述,英文手册1

· hp designjet z2100常见故障代码描述,英文手册

· hp designjet z3100ps常见故障代码描述,英文手册

· hp designjet z3200ps常见故障代码描述,英文手册

· hp designjet z5200常见故障代码描述,英文手册

· hp designjet z5200ps常见故障代码描述,英文手册

· hp designjet z5400ps常见故障代码描述,英文手册2

· hp designjet z5400ps常见故障代码描述,英文手册1

· hp designjet z6100常见故障代码描述,英文手册2

· hp designjet z6100常见故障代码描述,英文手册1

· hp designjet z6200常见故障代码描述,英文手册2

· hp designjet z6200常见故障代码描述,英文手册1

· hp designjet z6600常见故障代码描述,英文手册1

· hp designjet z6600常见故障代码描述,英文手册2

· hp designjet z6800常见故障代码描述,英文手册2

· hp designjet z6800常见故障代码描述,英文手册1

· hp laserjet 1000常见故障代码描述,英文手册

· hp laserjet 1010常见故障代码描述,英文手册

· hp laserjet 1012常见故障代码描述,英文手册

· hp laserjet 1015常见故障代码描述,英文手册

· hp laserjet 1018常见故障代码描述,英文手册

· hp laserjet 4000常见故障代码描述,英文手册

· hp laserjet 4050常见故障代码描述,英文手册

· hp laserjet 2100常见故障代码描述,英文手册

· hp laserjet 1020常见故障代码描述,英文手册

· hp laserjet 1022常见故障代码描述,英文手册

推荐文章
· hp500 数据线引发的古怪故障 系统错误:22:10

· hp1213 提示“扫描仪错误 13 ”是什么原因

· hp1300 开机机器有动作 三个灯交替亮 然后就一直闪报错灯,故障原因

· hp3300有时正常有时检测不到扫描头怎么处理?

· hp laserjet p1008 打印机 两端有字而中间出现无字是什么问题

· hp3055开机一直显示hewlett-packard,箭头跑到一半就不跑了,定哪了请各位大侠指点哈

· hp2300打印机,提示打印碳粉盒使用寿命已到,怎么解决

· hp3210

· hplaserjetpro300colorm351a出现error58.04

· hp1215彩色激光打印机~!现在打印出现4色横线在纸张上,请问如何处理

· hp7000打印后出白纸,后来黄灯常亮,不进纸是怎么回事儿

· hp order a cartridge

· hp4525机器报59.f0是什么错误?

· hp打印机不认墨盒

· hp5500绘图仪,打印机打印时出现0c00400000020c

· hp5200n打印机打印一个东西显示什么服务请求已接受

· hp5225怎么恢复出厂

· hplaserjetpro400mfp打印时显示50.2定音影器错误,是怎么回事?

· hp3015 报错50.10 怎么回事?

· hpj4580显示托架被卡住,打开打印托架检修门,清除卡塞?是哪出问题求大神指教

· hp1025 报错硒鼓错误.

· hpc7280开机老提示后面卡纸,但无纸,谁碰到过,怎么处理

· hp4525定影器和转印组件提示寿命到了,谁知道怎么清掉

· hpcp1025提示热凝器错误原因

· hp 提示59.c0错误

· hpcp1025打印一半清楚一半不清楚

· hp1215打印机显示青色碳粉盒内存错误是什么意思?

· hp3055打印机报scannererror3错误是什么问题

· hp3600齿轮组对位调整方法

· hp1108打印机上有个感叹号的灯显示红色,不打印是怎么回事?

· hp1106打印机感叹号灯一直闪,是什么故障

· hp1025彩色打印机显示有错误三角形里一个感叹号

· hp1025彩色激光打印机出现三角形灯一直亮,是什么故障

· hp5025报52.20代码错误

· hp1020打印一张时,后面跟了一张空白纸、卡纸等故障

· hp1025报错三角叹号和半圆灯同时亮问题

· hp5200l提示代码57.03错误

· hp2055d机换了定影膜之后开机自检过不去

· hp1108检测不到硒鼓,是怎么回事

· hp3050一体机,打印时总提示是50fusererror,是怎么回事

· hp2055d的维修手册

· hporder-a-cartridge按错键,打印机没反映了,有很多英文字母,不知道是怎么回事

· hp1010照片打印机打出的照片发黄,缺红色为什么?

· hp1536一体打印机总是出现在复印的时候出现(初始化)是怎么回事

· hpp1106开机后绿灯黄灯常亮,不能打印是什么故障。

· hp1106开机报警灯长亮(红灯)

· hp1106新机开机红黄灯常亮自检不了

· hp3600显示10.92.00墨盒未齿合

· hp1536复印时提示49错误,是什么原因

· hpm1216扫描到出现videoinitializeerror