上门维修电话696l6769,> 维修资料 > hp > 苏州HP DesignJet T1120售后维修电话696l6769> 苏州hp打印机维修服务网

hp DesignJet T1120常见故障代码描述,英文手册1

Code: 01.0:YZ
Description:
Communication with Engine PCA failed
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Remove the Formatter and reinsert it again. Ensure that it connects properly in the Engine PCA connector. • Replace the Engine PCA. • Replace the Formatter.
Code: 01.1:YZ
Description:
Error in the Engine PCA
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Engine PCA. 3. Replace the Formatter.
Code: 01.2:YZ
Description:
Failure communicating with an Ink Supply
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Perform the Ink Delivery System diagnostic test. – If the test finds that the ink supply is defective, replace it. – If the test does not find any errors, remove all the ink supplies from the ISS and reboot the product. 3. Install the ink cartridges with the product booted in normal mode. Use the replacement option available from the Touch Control Panel and install the cartridges one by one. If an error appears after installing a supply, the last supply you installed is defective. Replace it. 4. Check that the cables between the Left Ink Supply Station and the Engine PCA are not damaged and are correctly connected. In case of any damage replace the cables; see Connecting the Data Harness and ISS Harness Cable 5. Replace the Left Ink Supply Station. See Left Ink Supply Station. 6. Replace the Engine PCA. See EE Box.
Code: 02.1:YZ
Description:
Problem with the Carriage PCA
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Trailing Cable is not damaged. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA. 3. Replace the Carriage PCA. See Carriage PCA. 4. Replace the Trailing Cable and Carriage PCA Covers. 5. Replace the Engine PCA. See EE Box.
Code: 03.0:10
Description:
Battery of Real Time Clock ran down
Remedy:
Replace the battery.
Code: 03:YZ
Description:
Problem with Power Supply Unit
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Power Supply Unit (PSU). See Power Supply Unit
Code: 06:YZ
Description:
Failure reading/writing NVM in Hard disk
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Replace the Hard Disk.
Code: 07.01:11
Description:
DelSol3 ASIC not found or not responding
Remedy:
1. Check the condition and connections of the Interconnect data and power cable, replace if necessary

Code: 07.02:11
Description:
USB Cable not connected
Remedy:
1. Check the condition and connections of the USB cable, replace if necessary.
Code: 07.03:10
Description:
USB Hub not found
Remedy:
1. Make sure Interconnect board connector labeled 'INPUT HUB' is properly connected. 2. Make sure Wukong board connector labeled JUSB2 is properly connected to the cable coming from Interconnect board. 3. If failure continues, troubleshoot the error by changing the USB cable from Engine PCA to Interconnect, if the error follows to the changed part the USB cable is faulty, if it does not, the part is faulty. 4. Replace the Interconnect PCA, see Interconnect PCA. 5. Replace the Formatter Board see Formatter 6. Replace the Engine PCA
Code: 07.03:11
Description:
USB Scanner connected to incorrect port
Remedy:
Ensure that the USB cable from the Scanner to the Interconnect board is connected at the connection labeled 'SCANNER' and not 'HOST CON'
Code: 07:10
Description:
Interconnect Board or Power cable has failed
Remedy:
1. Check the condition and connections of the Power Cable, replace if necessary. 2. Replace the Interconnect Board
Code: 08:01:11
Description:
Touch Control Panel USB Cable fails
Remedy:
1. Check the condition and connections of the Touch Control Panel USB cable, replace if necessary. 2. If the error continues, replace the Touch Control Panel Touch Control Panel
Code: 08:04
Description:
Touch Control Panel communication to the product functions at the initialization, but during normal working the communication is lost.
Remedy:
1. Check the event log at the EWS support pages to see if there is another SE (for instance 07:10) and troubleshoot the problem more accurately.Appendix C: Obtaining the product log and the diagnostics package 2. Turn off the product and turn on again, and check to see if the error remains. 3. Upgrade the firmware For more information, see Appendix B: Emergency firmware upgrade with USB flash drive 4. Replace the HDD, see Hard Disk Drive 5. Escalate the issue.
Code: 08:08
Description:
A feature on the Touch Control Panel hangs or will not function (copy,scan etc)
Remedy:
1. Turn off the product and turn on again, and check to see if the error remains. 2. Upgrade the firmware For more information, see Appendix B: Emergency firmware upgrade with USB flash drive 3. Escalate the issue.
Code: 08:11
Description:
No communication between the product and the Touch Control Panel
Remedy:
1. Check the event log at the EWS support pages to see if there is another SE (for instance 07:10) and troubleshoot the problem more accurately.Appendix C: Obtaining the product log and the diagnostics package 2. Check the LED’s on the formatter to see if there is another issue and troubleshoot it more accurately. 3. Turn off the product and turn on again, and check to see if the error remains. 4. Upgrade the firmware 5. Check the condition of the USB cable, check it is not damaged or incorrectly connected. Reconnect USB cable (from Engine PCA to the Interconnect PCA or from Interconnect PCA to the Touch Control Panel 6. Replace the USB cable 7. Replace the Interconnect PCA, see Interconnect PCA. 8. Replace the Engine PCA see EE Box 9. If the error continues, replace the Touch Control Panel Touch Control Panel

Code: 09.01:10
Description:
Scanner Motor is failing
Remedy:
1. Perform the Scanner motor diagnostics. 2. Replace the Scanner Motor Scanner Motor Assembly (MFP only)
Code: 09.02:10
Description:
CIS A Element is failing
Remedy:
Replace CIS A Element CIS Element (MFP only)
Code: 09.03:10
Description:
CIS B Element is failing
Remedy:
Replace CIS B Element CIS Element (MFP only)
Code: 09.04:10
Description:
CIS C Element is failing
Remedy:
Replace CIS C Element CIS Element (MFP only)
Code: 09.05:10
Description:
CIS D Element is failing
Remedy:
Replace CIS D Element CIS Element (MFP only)
Code: 09.06:10
Description:
CIS E Element is failing
Remedy:
Replace CIS E Element CIS Element (MFP only)
Code: 09.08:11
Description:
Power cable of the Scanner is failing
Remedy:
Check the condition and connections of the Scanner Power cable, if necessary replace the cable.
Code: 09.09:11
Description:
USB cable of the Scanner is failing
Remedy:
Check the condition and connections of the Scanner USB cable, if necessary replace the cable.
Code: 09.10:04
Description:
Scanner is in SAFE MODE
Remedy:
Restart the product, if the problem persists replace the SCU. See Scanner Controller Board (MFP only).
Code: 09.10:10
Description:
Scanner SCU is failing
Remedy:
Replace the Scanner SCU.See Scanner Controller Board (MFP only).
Code: 09:01
Description:
Media jam in Scanner
Remedy:
1. Open the CIS to solve the media jam and close it again. 2. If no paper is seen, run Scanner Motor Diagnostic, refer to the Users Guide for further details.
Code: 09:02
Description:
Scanner not calibrated
Remedy:
Calibrate the Scanner
Code: 09:03
Description:
File I/O Error
Remedy:
Reboot Product
Code: 09:04
Description:
Contex Library failed to load
Remedy:
1. Reboot the Product 2. Upgrade the firmware For more information
Code: 11:YZ
Description:
Trailing Cable does not seem to be detected
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Trailing Cable is not damaged; replace it if necessary. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA. 3. Replace the Carriage PCA. See Carriage PCA. 4. Replace the Engine PCA. See EE Box.
Code: 21.1:YZ
Description:
Failure moving the Primer Motor of the Service Station
Remedy:
1. Remove the Right Cover and make sure the cables from the Engine PCA to the Service Station are connected and are not damaged. In case of any damage replace the affected cable; see Engine Cables Kit 2. Perform the Primer Motor diagnostic test (listed under the service station diagnostic test) to troubleshoot the problem further. See Primer motor. 3. Replace the Service Station. See Service Station.

Code: 21.2:YZ
Description:
Failure testing the length of the Service Station path
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product. 2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. 3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. It may happen that the cutter is blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage. 4. Perform the Service Station diagnostic test to troubleshoot the problem further. See Service Station Test. 5. Replace the Service Station. See Service Station.
Code: 21:YZ
Description:
Failure moving Service Station
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product. 2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. 3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. The cutter may be blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage. 4. Perform the Service Station diagnostic test to troubleshoot the problem further. See Service Station Test. 5. Replace the Service Station. See Service Station.
Code: 22.0:YZ
Description:
Left Ink Supply Station error, module 0.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable. 3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further. See Ink Delivery System (IDS) Test. 4. Replace the Left Ink Supply Station. See Left Ink Supply Station. 5. Replace the Engine PCA. See EE Box.
Code: 22.1:YZ
Description:
Left Ink Supply Station error, module 1
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable. NOTE: Check the Data Harness and ISS Harness Cable are connected in the right position onto the Engine PCA. These two connectors can be swapped by mistake causing a SE 22.1:10. Check the instructions in Connecting the Data Harness and ISS Harness Cable 3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further. See Ink Delivery System (IDS) Test. 4. Replace the Left Ink Supply Station. See Left Ink Supply Station. 5. Replace the Engine PCA. See Starwheel Assembly.
Code: 24:YZ
Description:
Ink Setup failure
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Insert the new purgers, reconnect the power cord and power on the product. 2. Perform the Ink Delivery System diagnostic test in order to check that the bongos (pushers) go up and down to pressurize ink in the tubes and the Out of Ink sensors work properly. See Ink Delivery System (IDS) Test. 3. Try purging the Ink Supply Tubes again once the product has been restarted. 4. If the diagnostic test does not find any problem, install new cartridges in the product and try purging the Ink Supply Tubes again. It could be that one of the cartridges is defective. 5. If the problem persists, replace the Ink Supply Tubes. You must bring purgers and ink cartridges. See Ink Supply Tubes & Trailing Cable.
Code: 26:01
Description:
Ink supply error found during IDS diagnostic test. In the Touch Control Panel message you will see letters representing the names of the colors of the faulty supplies.
Remedy:
1. Reseat the faulty ink supply and repeat the Ink Delivery System diagnostic test. 2. If the problem persists, replace the faulty ink supply and repeat the Ink Delivery System diagnostic test. 3. If the problem persists, replace the Left Ink Supply Station. See Left Ink Supply Station.
Code: 39.1:01
Description:
Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.
Remedy:
There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 1 in standby or resume operation.
Code: 39.2:01
Description:
Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.
Remedy:
There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 2 in standby or resume operation.

Code: 41:YZ
Description:
Electrical fault or current limit in Media-Axis Motor
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Media Advance Roller. If there is a wrinkled mass of paper inside the paper path, lift the Pinch wheels (using Media Lever) and clear the obstruction. 3. Perform the Paper Drive diagnostic test to troubleshoot the problem furthe. See Paper Drive Test. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Check that the Media Advance Drive cable is not damaged and is correctly connected to the Engine PCA. 6. Replace the Media Advance Drive. See Media Advance Drive. 7. Replace the Engine PCA. See EE Box.
Code: 42:YZ
Description:
Electrical problem (fault, current limit, overheating) in Scan-Axis Motor
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Carriage Assembly. Remove any obstacle to let the carriage move freely along the whole scan axis. If there is a wrinkled mass of paper inside the paper path, raise the pinch wheels (using the Media Lever) and clear the obstruction. 3. Check that the Scan-Axis Motor cable is not damaged and is correctly connected to the Engine PCA. 4. Replace the Scan-Axis Motor. See Scan-axis Motor. 5. Replace the Engine PCA. See EE Box.
Code: 45.1:YZ
Description:
An error with the Rewinder 1 System (Upper Rewinder) has been detected.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Remove the paper from Roll 1. Reconnect the power cord and power on the product. 2. Check that the Rewinder 1 cable is not damaged and is correctly connected to the Engine PCA. 3. Check that the Upper Right Roll Support is correctly attached to and aligned with the Right Cover. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Replace the Upper Right Roll Support. See Roll Support, Upper Right.
Code: 45.2:YZ
Description:
An error with the Rewinder 2 System (Lower Rewinder) has been detected .
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Remove the paper from Roll 2. Reconnect the power cord and power on the product. 2. Check that the Rewinder 2 cable is not damaged and is correctly connected to the Engine PCA. 3. Check that the Lower Right Roll Support is correctly attached to and aligned with the Right Cover. 4. Perform the Rewinder diagnostic test to troubleshoot the problem further. See Rewinder Test. 5. Replace the Lower Right Roll Support. See Roll Support, Lower Right.
Code: 47:YZ
Description:
Starwheels motor error
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check for any visible obstacles restricting the movement of the Starwheel Assembly, then clear the obstruction. 3. Check that the Starwheel Assembly cable is not damaged and is correctly connected to the Engine PCA. 4. Perform the Scan Axis Starwheel diagnostic test to troubleshoot the problem further. 5. Replace the Starwheel Motor. See Starwheel Motor. 6. Replace the Engine PCA. See EE Box.
Code: 48:YZ
Description:
PPS system failure
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Pen to Paper Space (PPS) Solenoid cable is not damaged and is correctly connected to the Engine PCA. 3. Perform the Scan Axis PRS diagnostic test to troubleshoot the problem further. 4. Replace the Pen to Paper Space (PPS) Solenoid. See Pen to Paper Space (PPS) Solenoid. 5. Replace the Engine PCA. See EE Box.
Code: 51:YZ
Description:
Scanner Position Sensor failure
Remedy:
1. Check that the Scanner Position Sensor cable is not damaged and is correctly connected to the Engine PCA. 2. Perform the Sensors Test to troubleshoot the problem further. See Sensors Test. 3. Replace the Scanner Position Sensor. See Scanner Position Sensor (MFP only).
Code: 52:10
Description:
The product has detected a failure in the Drop Detector.
Remedy:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product. 2. Check that the Drop Detector cable is not damaged and is correctly connected to the Engine PCA. 3. Replace the Drop Detector. See Drop Detector. 4. Replace the Engine PCA. See EE Box.

热门图文

相关资料补充


热门关注
· hp designjet t120常见故障代码描述,英文手册

· hp designjet t1200常见故障代码描述,英文手册2

· hp designjet t1200常见故障代码描述,英文手册1

· hp designjet t1300常见故障代码描述,英文手册2

· hp designjet t1300常见故障代码描述,英文手册1

· hp designjet t1500常见故障代码描述,英文手册2

· hp designjet t1500常见故障代码描述,英文手册1

· hp designjet t1520常见故障代码描述,英文手册2

· hp designjet t1520常见故障代码描述,英文手册1

· hp designjet t2300常见故障代码描述,英文手册2

· hp designjet t2300常见故障代码描述,英文手册1

· hp designjet t2500常见故障代码描述,英文手册2

· hp designjet t2500常见故障代码描述,英文手册1

· hp designjet t2530常见故障代码描述,英文手册2

· hp designjet t2530常见故障代码描述,英文手册1

· hp designjet t3500常见故障代码描述,英文手册2

· hp designjet t3500常见故障代码描述,英文手册1

· hp designjet t520常见故障代码描述,英文手册

· hp designjet t610常见故障代码描述,英文手册1

· hp designjet t610常见故障代码描述,英文手册2

· hp designjet t620常见故障代码描述,英文手册2

· hp designjet t620常见故障代码描述,英文手册1

· hp designjet t7100常见故障代码描述,英文手册3

· hp designjet t7100常见故障代码描述,英文手册2

· hp designjet t7100常见故障代码描述,英文手册1

· hp designjet t7200常见故障代码描述,英文手册3

· hp designjet t7200常见故障代码描述,英文手册2

· hp designjet t7200常见故障代码描述,英文手册1

· hp designjet t730常见故障代码描述,英文手册2

· hp designjet t730常见故障代码描述,英文手册1

推荐文章
· hpcp5225恢复出厂设置

· hp177fw一体机新机提示安装成像鼓

· 佳能mf4452报警:e2020002接触式传感器hp错误,回路故障

· hp2055扫描打印复印一体机,显示printingdocument然后无反映故障

· hp1005纸刚出定影组件就卡住

· hp2055d开机提示52扫描仪错误

· hp128提示文档进纸器拾取错误

· hpm128fp故障灯一直闪控制面板无显示

· hp126nw提示正在使用用过的碳粉盒

· hpt790绘图仪错误代码79:03

· 79errorhp2600

· hp176开机时为什么电源灯旁的感叹号闪烁

· hpm1213nf打印一张通路卡纸

· hp1055cmip地址查询

· hp-mfpm176n加了粉还提示墨粉量低

· hp3630墨盒加墨水图解

· hp3035错误信息49.ff04

· hplaserjet1100serues显示感叹号

· hpm176一直提示三角感叹号错误是怎么回事

· hp1112开机灯闪烁

· hp系统错误7904关闭电源如果问题仍存在,请致电hp支持中心

· hpp2055d提示49err3d910c8怎么解决

· hpm1005复印薄的文稿有黑影

· hp226dw提示扫描仪错误17关闭然后打开

· hp1280电源灯不亮的真正原因

· hpp1606n不进纸,是什么问题

· hp2025彩色打印机报错59是哪里的问题

· ricohprintersc680

· hpm128fp开机一直显示正在初始化

· hp1319f屏幕 无显

· hp m1005一体机安装程序错误,rpc服务器不可用

· hp m1005 开机报scanner error 20错误,故障原因

· hp1020/hp1020plus/hp1010/hp1007定影器故障夹纸原因

· hp1008打印文稿纸中间有白道,字体模糊?

· hp1005经常夹纸,并且纸夹在定影器处

· hp1213收发不了传真问题

· hp1025彩色打印机加粉步骤

· hp5200打印白纸,无字问题原因

· hp1025机器偏色校准

· hp5200lx提示13.20.00顶盖卡纸,解决方案

· hp1536解除密码方法

· hp1536打印机打印靠右侧坚向全白,换硒鼓打印故障以旧

· hp designjet 500 ,800系列打印机 - 打印结束后不裁纸并报错 6105

· hp t610/t1100显示要更换裁刀的处理方法

· hp500绘图仪是打印时每隔10cm就出现一次重影

· hp designjet 500与800打印内容左右有重影

· hp designjet 500 和 800 系列打印机 - 系统错误 6105 processing job

· hp designjet 100和110系列绘图仪报错误代码0113 错误代码

· hp designjet系列绘图仪打印线条失真如何解决

· hp designjet系列绘图仪喷嘴堵塞如何解决