hp Color LaserJet 4650常见故障代码描述,英文手册2
更新时间：2024/4/8 10:37:53,view:73HP Color LaserJet 4650打印机苏州东渚复印机维修服务中心电话0512-696l6769，苏州HP Color LaserJet 4650东渚维修站，HP Color LaserJet 4650东渚维修站, hp 203dw 指示灯, hp1108打印提示热凝器错误, hp227会自动打印乱码, hp1005不通电, hp1005打印打印完多进纸半张卡住,
Code: 51.2Y
Display:
51.2Y PRINTER ERROR
Description:
A laser beam error has occurred.
Y Description: 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Upgrade formatter and DC Controller firmware, which can be found in a single. 3. Reseat the connectors (J1002 - Y, J1003 - C, J1004 - M, J1005 - K) between the laser/scanner and DC controller PCB. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner
Code: 52.X
Display:
52.X PRINTER ERROR
Description:
A printer error has occurred.
X Description: 00 - Scanner error 01 - Scanner startup error 02 - Scanner rotation error
Y Description: 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Upgrade formatter and DC Controller firmware. 3. Reseat the connectors between the laser/scanner and DC controller PCB. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner.
Code: 53.XX.X
Display:
53.XX.X CHECK RAM DIMM SLOT X
Description:
A memory error has occurred.
X DIMM Type: 1 RAM Y Device Location 1 DIMM Slot 1 2 DIMM Slot 2
ZZ Error Number: 00 Unsupported memory 01 Unrecognized memory 02 Unsupported memory size 03 Failed RAM test 04 Exceeded maximum RAM size 05 Invalid DIMM speed
Remedy:
If prompted to do so, press to continue. The printer should come to the Ready state, but will not make full use of all memory installed. Otherwise: 1. Turn the printer off. 2. Verify that all memory meets specifications and is correctly seated. 3. Turn the printer on. 4. If the problem persists, replace the DIMM card in the slot indicated.
Code: 54.XX
Display:
54.XX PRINTER ERROR
Description:
Printing cannot continue. There is a sensor malfunction. Values of XX are: 01 - Temperature/humidity sensor (J1010 environment sensor) 15 - Yellow toner remaining sensor (J1014 toner level sensor) 16 - Magenta toner remaining sensor (J1014 toner level sensor) 17 - Cyan toner remaining sensor (J1014 toner level sensor) 18 - Black toner remaining sensor (J1014 toner level sensor)
Remedy:
1. Turn the printer off then on. 2. Check the connectors: J501 on the toner level PCB or J5201 on the environment sensor. 3. Check the connectors: J1014 (toner lever sensor) or J1010 (environment sensor) on the DC controller PCB. 4. Replace the environment sensor or toner level detection PCB
Code: 55.X.X
Display:
55.X.X DC CONTROLLER ERROR
Description:
A printer command error has occurred.
Values of XX are: 01 - DC controller memory error 02 - DC controller memory error 03 - No engine response 04 - Communication error 05 - RFU error
Remedy:
01 – 02 errors Replace the DC controller. 03 – 04 errors 1. Reseat formatter 2. Check all connectors on the DC controller. 3. Upgrade formatter and DC Controller firmware. 4. Replace the DC controller PCB. 05 errors 1. Upgrade the DC controller PCB firmware. 2. Replace the DC controller PCB firmware.
Code: 56.XX
Display:
56.XX PRINTER ERROR
Description:
A printer error has occurred.
XX Description: 01 - Input device 02 - Output device
Remedy:
1. Turn the printer off then on. 2. Remove all input and output devices and reinstall them. 3. Check all connectors to the input/ output devices that are installed. Replace any damaged connectors.
Code: 57.0X
Display:
57.0X PRINTER ERROR
Description:
A printer fan error has occurred.
XX Description: 01 - Delivery fan 04 - Cartridge fan 05 - Duplex fan 07 - Upper exhaust fan 0A - Power supply fan J1033 - Measure pins 1 and 3 for cartridge fan J1033 - Measure pins 4 and 6 for delivery fan J1033 - Measure pins 7 and 9 for upper exhaust fan J1034 - Measure pins 1 and 3 for power supply fan
Remedy:
1. Turn the printer off then on. 2. Reconnect the connector J1004 on the DC controller PCB. 3. Immediately after starting the print operation, measure the voltage between the appropriate pins on the connector. If the voltage changes from 0 V to 24 V, replace the affected fan.
Code: 58.0X
Display:
58.0X PRINTER ERROR
Description:
A memory tag error was detected.
XX Description: 03 – Memory controller PCB 04 – Memory controller PCB power supply
Remedy:
1. Turn the printer off then on. 2. Check the connectors on the memory controller (J4001, J9630) and the DC controller PCB (J1021). 3. Replace the memory PCB. 4. Replace the E label contacts.
Code: 59.XY
Display:
59.XY PRINTER ERROR
Description:
A printer motor error has occurred.
X Description: 0 Motor error 1 Motor startup error 2 Motor rotation error 3 Fuser motor startup error 4 Fuser motor rotation error 5 Image drum motor startup error 6 Image drum motor rotation error 9 ETB motor startup error A ETB motor rotation error B Developing disengaging motor startup error C Developing disengaging motor rotation error Y Description 0 - Black or N/A 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Note: This message might also display if the transfer unit is missing or incorrectly installed. Ensure that the transfer unit is correctly installed. ETB motor error 1. Run the component test to verify that the ETB is working correctly. 2. Clean the ETB unit intermediate connector J4613. 3. Reconnect the connector J4613 between the ETB and the printer, and J1011 on the DC controller PCB. 4. Replace the ETB. Fuser motor error 1. Reconnect the connectors J4605 for the fuser motor and J1024 on the DC controller PCB. 2. Run the component test to verify that the fuser motor is working correctly. 3. Replace the fuser motor. Print cartridge motor error 1. Run the component test to verify that the print cartridge motor is working correctly. 2. Reconnect the print cartridge connector on the DC controller PCB (J1018 for magenta and black, J1017 for cyan and yellow). On the motor itself, reconnect the connectors (J4603 for magenta, J4604 for black, J4601 for yellow, and J4602 for cyan). 3. Replace the drum drive assembly for the indicated print cartridge Developing disengaging motor error 1. Run the component test to verify that the print developing disengaging motor is working correctly. 2. Reconnect the connectors J468 and J1020 between the developing disengaging motor and the DC controller PCB. 3. Replace the developing disengaging motor.
Code: 60.X
Display:
60.X PRINTER ERROR
Description:
A tray lifting error has occurred, where XX is the number of the tray
Remedy:
1. Turn the printer off then on. 2. Install the tray and listen carefully. You should be able to hear the paper stack being lifted. You can also watch the paper level indicator on the front of the tray to see if it moves. 3. Check the following connectors: • Tray 2: J4618 on the lifter motor and J1015 on the DC controller • Trays 3.6: J8120 on the lifter motor and J8102 on the paper feeder PCB 4. Replace the lifter motor assembly
Code: 62
Display:
62 NO SYSTEM
Description:
No system was found.
Remedy:
1. Turn the printer off then on. 2. Reseat the firmware compact flash, making sure that it is in the first slot. 3. Replace the firmware compact flash and the formatter.
Code: 65.X.X
Display:
65.X.X OUTPUT DEVICE CONDITION
Description:
An external output device has a condition that needs attention before printing can resume. The amber light on the stapler/ stacker is blinking.
XX Description: 10 - Jogger not detected, hp sensor off 11 - Jogger not detected, hp sensor on 12 - Eject lever not detected, hp sensor off 13 - Eject lever not detected, hp sensor on 14 - Paper hold lever not detected, hp sensor off 15 - Paper hold lever not detected, hp sensor on 16 - Paper hold lever over run
Remedy:
Remove any jammed paper and open and then close the top cover. If necessary, reseat the output device.
Code: 65.X.X
Display:
65.X.X OUTPUT DEVICE DISCONNECTED
Description:
Communication between the printer and the device has been broken. The device could be disconnected.
Remedy:
Turn the printer off. Replace the stapler/ stacker on the printer, making sure it is properly installed. Turn the printer on.
Code: 66.XX.X
Display:
66.XX.X OUTPUT DEVICE FAILURE
Description:
The stapler/stacker has failed. The amber light on the stapler/stacker is solid.
XX Description: 18 - Stapler could not detect the hp sensor 19 - Stapler could not advance the staples 20 - Safe switch detect unsafe 21 - Tray move-up time out 22 - Tray move-down time out 23 - Tray detect upper limit 24 - Tray detect bottom limit
Remedy:
1. Turn the printer off. 2. Check the staple cartridge for the staples jammed exiting the cartridge, and reseat staples in the cartridge if necessary. 3. Check the stapling bed for jammed paper or staples. Verify that the stapler cartridge is intact. 4. Check that nothing is obstructing the movement of the stapler/stacker. 5. Check that the output tray is properly installed and output tray is in the downmost position. 6. Turn the printer on.
Code: 68.X
Display:
68.X PERMANENT STORAGE FULL
Description:
A non-volatile storage device is full. Pressing the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press GO to continue. 2. For 68.0 errors, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 68.X
Display:
68.X PERMANENT STORAGE WRITE FAIL
Description:
A non-volatile storage device is full. Pressing the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press to continue. 2. For a 68.0 error, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 68.X
Display:
68.X STORAGE ERROR SETTINGS CHANGED
Description:
One or more printer settings saved in the non-volatile storage device is invalid and has been reset to its factory default. Pressing GO the button should clear the message. Printing can continue, but there may be unexpected behavior. 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press to continue. 2. For a 68.0 error, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 69.X
Display:
69.X PRINTER ERROR
Description:
A printer error has occurred.
X Description: 0 - duplexer not functioning 1 - duplexer not functioning
Remedy:
1. Check if the duplexer connector (J2003) is connected to the duplexer. 2. Check the connector (J1030) on the DC controller PCB. 3. Replace the duplexer.
Code: 79.XXXX
Display:
79.XXXX PRINTER ERROR
Description:
A critical hardware error has occurred.
Remedy:
1. Turn the printer off then on. 2. If the problem persists, reseat the firmware compact flash. 3. Reseat the formatter. 4. Upgrade the firmware compact flash. 5. Replace the firmware compact flash. 6. Replace the formatter. Calibrate the printer.
Code: 8X.YYYY
Display:
8X.YYYY EIO X ERROR
Description:
The I/O accessory card in slot X has encountered a critical error.
X Description
1: error in slot 1 2: error in slot 2
Remedy:
1. Turn the printer off then on. 2. If the problem persists, reseat the EIO card. 3. Replace the EIO card
Display:
51.2Y PRINTER ERROR
Description:
A laser beam error has occurred.
Y Description: 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Upgrade formatter and DC Controller firmware, which can be found in a single. 3. Reseat the connectors (J1002 - Y, J1003 - C, J1004 - M, J1005 - K) between the laser/scanner and DC controller PCB. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner
Code: 52.X
Display:
52.X PRINTER ERROR
Description:
A printer error has occurred.
X Description: 00 - Scanner error 01 - Scanner startup error 02 - Scanner rotation error
Y Description: 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Upgrade formatter and DC Controller firmware. 3. Reseat the connectors between the laser/scanner and DC controller PCB. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner.
Code: 53.XX.X
Display:
53.XX.X CHECK RAM DIMM SLOT X
Description:
A memory error has occurred.
X DIMM Type: 1 RAM Y Device Location 1 DIMM Slot 1 2 DIMM Slot 2
ZZ Error Number: 00 Unsupported memory 01 Unrecognized memory 02 Unsupported memory size 03 Failed RAM test 04 Exceeded maximum RAM size 05 Invalid DIMM speed
Remedy:
If prompted to do so, press to continue. The printer should come to the Ready state, but will not make full use of all memory installed. Otherwise: 1. Turn the printer off. 2. Verify that all memory meets specifications and is correctly seated. 3. Turn the printer on. 4. If the problem persists, replace the DIMM card in the slot indicated.
Code: 54.XX
Display:
54.XX PRINTER ERROR
Description:
Printing cannot continue. There is a sensor malfunction. Values of XX are: 01 - Temperature/humidity sensor (J1010 environment sensor) 15 - Yellow toner remaining sensor (J1014 toner level sensor) 16 - Magenta toner remaining sensor (J1014 toner level sensor) 17 - Cyan toner remaining sensor (J1014 toner level sensor) 18 - Black toner remaining sensor (J1014 toner level sensor)
Remedy:
1. Turn the printer off then on. 2. Check the connectors: J501 on the toner level PCB or J5201 on the environment sensor. 3. Check the connectors: J1014 (toner lever sensor) or J1010 (environment sensor) on the DC controller PCB. 4. Replace the environment sensor or toner level detection PCB
Code: 55.X.X
Display:
55.X.X DC CONTROLLER ERROR
Description:
A printer command error has occurred.
Values of XX are: 01 - DC controller memory error 02 - DC controller memory error 03 - No engine response 04 - Communication error 05 - RFU error
Remedy:
01 – 02 errors Replace the DC controller. 03 – 04 errors 1. Reseat formatter 2. Check all connectors on the DC controller. 3. Upgrade formatter and DC Controller firmware. 4. Replace the DC controller PCB. 05 errors 1. Upgrade the DC controller PCB firmware. 2. Replace the DC controller PCB firmware.
Code: 56.XX
Display:
56.XX PRINTER ERROR
Description:
A printer error has occurred.
XX Description: 01 - Input device 02 - Output device
Remedy:
1. Turn the printer off then on. 2. Remove all input and output devices and reinstall them. 3. Check all connectors to the input/ output devices that are installed. Replace any damaged connectors.
Code: 57.0X
Display:
57.0X PRINTER ERROR
Description:
A printer fan error has occurred.
XX Description: 01 - Delivery fan 04 - Cartridge fan 05 - Duplex fan 07 - Upper exhaust fan 0A - Power supply fan J1033 - Measure pins 1 and 3 for cartridge fan J1033 - Measure pins 4 and 6 for delivery fan J1033 - Measure pins 7 and 9 for upper exhaust fan J1034 - Measure pins 1 and 3 for power supply fan
Remedy:
1. Turn the printer off then on. 2. Reconnect the connector J1004 on the DC controller PCB. 3. Immediately after starting the print operation, measure the voltage between the appropriate pins on the connector. If the voltage changes from 0 V to 24 V, replace the affected fan.
Code: 58.0X
Display:
58.0X PRINTER ERROR
Description:
A memory tag error was detected.
XX Description: 03 – Memory controller PCB 04 – Memory controller PCB power supply
Remedy:
1. Turn the printer off then on. 2. Check the connectors on the memory controller (J4001, J9630) and the DC controller PCB (J1021). 3. Replace the memory PCB. 4. Replace the E label contacts.
Code: 59.XY
Display:
59.XY PRINTER ERROR
Description:
A printer motor error has occurred.
X Description: 0 Motor error 1 Motor startup error 2 Motor rotation error 3 Fuser motor startup error 4 Fuser motor rotation error 5 Image drum motor startup error 6 Image drum motor rotation error 9 ETB motor startup error A ETB motor rotation error B Developing disengaging motor startup error C Developing disengaging motor rotation error Y Description 0 - Black or N/A 1 - Cyan 2 - Magenta 3 - Yellow
Remedy:
1. Turn the printer off then on. 2. Note: This message might also display if the transfer unit is missing or incorrectly installed. Ensure that the transfer unit is correctly installed. ETB motor error 1. Run the component test to verify that the ETB is working correctly. 2. Clean the ETB unit intermediate connector J4613. 3. Reconnect the connector J4613 between the ETB and the printer, and J1011 on the DC controller PCB. 4. Replace the ETB. Fuser motor error 1. Reconnect the connectors J4605 for the fuser motor and J1024 on the DC controller PCB. 2. Run the component test to verify that the fuser motor is working correctly. 3. Replace the fuser motor. Print cartridge motor error 1. Run the component test to verify that the print cartridge motor is working correctly. 2. Reconnect the print cartridge connector on the DC controller PCB (J1018 for magenta and black, J1017 for cyan and yellow). On the motor itself, reconnect the connectors (J4603 for magenta, J4604 for black, J4601 for yellow, and J4602 for cyan). 3. Replace the drum drive assembly for the indicated print cartridge Developing disengaging motor error 1. Run the component test to verify that the print developing disengaging motor is working correctly. 2. Reconnect the connectors J468 and J1020 between the developing disengaging motor and the DC controller PCB. 3. Replace the developing disengaging motor.
Code: 60.X
Display:
60.X PRINTER ERROR
Description:
A tray lifting error has occurred, where XX is the number of the tray
Remedy:
1. Turn the printer off then on. 2. Install the tray and listen carefully. You should be able to hear the paper stack being lifted. You can also watch the paper level indicator on the front of the tray to see if it moves. 3. Check the following connectors: • Tray 2: J4618 on the lifter motor and J1015 on the DC controller • Trays 3.6: J8120 on the lifter motor and J8102 on the paper feeder PCB 4. Replace the lifter motor assembly
Code: 62
Display:
62 NO SYSTEM
Description:
No system was found.
Remedy:
1. Turn the printer off then on. 2. Reseat the firmware compact flash, making sure that it is in the first slot. 3. Replace the firmware compact flash and the formatter.
Code: 65.X.X
Display:
65.X.X OUTPUT DEVICE CONDITION
Description:
An external output device has a condition that needs attention before printing can resume. The amber light on the stapler/ stacker is blinking.
XX Description: 10 - Jogger not detected, hp sensor off 11 - Jogger not detected, hp sensor on 12 - Eject lever not detected, hp sensor off 13 - Eject lever not detected, hp sensor on 14 - Paper hold lever not detected, hp sensor off 15 - Paper hold lever not detected, hp sensor on 16 - Paper hold lever over run
Remedy:
Remove any jammed paper and open and then close the top cover. If necessary, reseat the output device.
Code: 65.X.X
Display:
65.X.X OUTPUT DEVICE DISCONNECTED
Description:
Communication between the printer and the device has been broken. The device could be disconnected.
Remedy:
Turn the printer off. Replace the stapler/ stacker on the printer, making sure it is properly installed. Turn the printer on.
Code: 66.XX.X
Display:
66.XX.X OUTPUT DEVICE FAILURE
Description:
The stapler/stacker has failed. The amber light on the stapler/stacker is solid.
XX Description: 18 - Stapler could not detect the hp sensor 19 - Stapler could not advance the staples 20 - Safe switch detect unsafe 21 - Tray move-up time out 22 - Tray move-down time out 23 - Tray detect upper limit 24 - Tray detect bottom limit
Remedy:
1. Turn the printer off. 2. Check the staple cartridge for the staples jammed exiting the cartridge, and reseat staples in the cartridge if necessary. 3. Check the stapling bed for jammed paper or staples. Verify that the stapler cartridge is intact. 4. Check that nothing is obstructing the movement of the stapler/stacker. 5. Check that the output tray is properly installed and output tray is in the downmost position. 6. Turn the printer on.
Code: 68.X
Display:
68.X PERMANENT STORAGE FULL
Description:
A non-volatile storage device is full. Pressing the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press GO to continue. 2. For 68.0 errors, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 68.X
Display:
68.X PERMANENT STORAGE WRITE FAIL
Description:
A non-volatile storage device is full. Pressing the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press to continue. 2. For a 68.0 error, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 68.X
Display:
68.X STORAGE ERROR SETTINGS CHANGED
Description:
One or more printer settings saved in the non-volatile storage device is invalid and has been reset to its factory default. Pressing GO the button should clear the message. Printing can continue, but there may be unexpected behavior. 0 for onboard NVRAM 1 for removable disk (flash or hard)
Remedy:
1. Press to continue. 2. For a 68.0 error, turn the printer off then on. 3. If a 68.0 error persists, perform an NVRAM initialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive or flash card. 5. For 68.1 errors that persist, reinitialize the hard disk or flash card.
Code: 69.X
Display:
69.X PRINTER ERROR
Description:
A printer error has occurred.
X Description: 0 - duplexer not functioning 1 - duplexer not functioning
Remedy:
1. Check if the duplexer connector (J2003) is connected to the duplexer. 2. Check the connector (J1030) on the DC controller PCB. 3. Replace the duplexer.
Code: 79.XXXX
Display:
79.XXXX PRINTER ERROR
Description:
A critical hardware error has occurred.
Remedy:
1. Turn the printer off then on. 2. If the problem persists, reseat the firmware compact flash. 3. Reseat the formatter. 4. Upgrade the firmware compact flash. 5. Replace the firmware compact flash. 6. Replace the formatter. Calibrate the printer.
Code: 8X.YYYY
Display:
8X.YYYY EIO X ERROR
Description:
The I/O accessory card in slot X has encountered a critical error.
X Description
1: error in slot 1 2: error in slot 2
Remedy:
1. Turn the printer off then on. 2. If the problem persists, reseat the EIO card. 3. Replace the EIO card
热门图文