HP Color LaserJet 2700常见故障代码描述,英文手册

Code: -
Display:
Device error Press OK
Description:
A beam-detect error has occurred.
Remedy:
1. Press OK to continue. 2. If the message persists, turn the printer off then on.
Code: -
Display:
Door open
Description:
If the top cover and front door are closed, the problem might be with the connections for the door-detection switch.
Remedy:
Close the top cover and front door. 1. Make sure the top cover and front door are closed. 2. If the message persists, make sure the following connectors are seated correctly: On the driver PCA, connectors J201, J202, and J203. On the DC controller, connectors J1022 and J1024. 3. Replace the DC controller PCA.
Code: -
Display:
Engine comm. error
Description:
The printer experienced an internal communication error.
Remedy:
NOTE This is a warning message only. Output might be affected. 1. Plug the printer into a different power outlet. 2. Try a different power cord. 3. Disconnect all cables except the power cord. Turn the printer off and then on. 4. Make sure all orange packing material has been removed from inside the printer.
Code: 10.0000
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Black e-label memory error
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.0001
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Cyan e-label memory error
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.0002
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Magenta e-label memory error
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.0003
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Yellow e-label memory error
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.1000
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Black e-label missing
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.

Code: 10.1001
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Cyan e-label missing
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.1002
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Magenta e-label missing
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 10.1003
Display:
10.XXXX Supply Error Reinstall
Description:
The printer cannot read or write to at least one print cartridge memory tag, or at least one memory tag is missing.
Yellow e-label missing
Remedy:
1. Open the front door. 2. Remove the print cartridges, and then reinstall them. 3. Close the front door. 4. Turn the printer off and then on. 5. Clean the memory controller PCA contacts to the memory tag if they are dirty. 6. Replace the memory controller PCA if necessary. 7. Replace the DC controller PCA if necessary.
Code: 49
Display:
49 Error Turn off then on
Description:
A critical firmware error has occurred.
Remedy:
1. Turn the printer off and then on. 2. Try printing a job from a different program. If the job prints, try printing a different file from the original program. If the message appears only with a certain program or print job, contact the software vendor for assistance. 3. If the message persists with different programs and print jobs, disconnect all of the printer cables that connect to the network or the computer. 4. Turn the printer off. 5. Remove all memory DIMMs or thirdparty DIMMs from the printer. (Do not remove the firmware DIMM in the lower slot J1). 6. Remove the printer EIO card. 7. Turn the printer on. 8. If the error does not persist, install each DIMM and EIO device one at a time. Turn the printer off and then on again after installing each device. 9. Replace DIMMs and EIO devices as necessary. 10. Reconnect all of the printer cables. 11. If the error persists, replace the firmware DIMM. 12. Replace the formatter and calibrate the printer.
Code: 50.1
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
Low fuser temperature
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. 3. Turn off the printer. 4. Remove the fuser. 5. If there is no conduction in the main thermistor, measure the resistance between fuser connectors J6007LA-1 and J6007LA-3. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. 6. If there is no conduction in the fuser heater, measure the resistance between fuser connectors J6007LAF-1 and J6007-2. If the resistance is not 5 ohms to 1 kohms (100 to 127 V) or 20 ohms to 1 kohms (220 to 240 V), replace the fuser. 7. Replace the DC controller PCA.
Code: 50.2
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
Fuser-warmup service
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. 3. Turn off the printer. 4. Remove the fuser. 5. If there is no conduction in the subthermistor, measure the resistance between fuser connectors J6007LA-2 and J6007LA-3. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. 6. If there is no conduction in the fuser heater, measure the resistance between fuser connectors J6007LAF-1 and J6007-2. If the resistance is not 5 ohms to 1 kohms (100 to 127 V) or 20 ohms to 1 kohms (220 to 240 V), replace the fuser. 7. Replace the DC controller PCA.
Code: 50.3
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
High fuser temperature
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. 3. Turn off the printer. 4. Remove the fuser. 5. Measure the resistance between fuser connectors J6007LA-1 and J6007LA-3. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. 6. Replace the DC controller PCA.
Code: 50.4
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
Faulty fuser
Remedy:
1. Improve the power supply if the power supply frequency is not 40 to 70 Hz. 2. Replace the low-voltage power-supply PCA. 3. Replace the DC controller PCA.


Code: 50.7
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
Fuser pressure release mechanism failure
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that fuser connector J705, fuser motor connector J5008, and driver PCA connector J213 are seated correctly. 3. Replace the fuser drive assembly. 4. Replace the DC controller PCA.
Code: 50.8
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
Low fuser temperature (subthermistor)
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. 3. Turn off the printer. 4. Remove the fuser. 5. If there is no conduction in the subthermistor, measure the resistance between fuser connectors J6007LA-1 and J6007LA-3. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. 6. If there is no conduction in the fuser heater, measure the resistance between fuser connectors J6007LAF-1 and J6007-2. If the resistance is not 5 ohms to 1 kohms (100 to 127 V) or 20 ohms to 1 kohms (220 to 240 V), replace the fuser. 7. Replace the DC controller PCA.
Code: 50.9
Display:
50.X Fuser Error Turn off then on
Description:
A fuser error has occurred.
High fuser temperature (subthermistor)
Remedy:
1. Verify the fuser is installed correctly and fully seated. 2. Check that connector J6007 on the fuser is seated correctly. Replace the connector as necessary. 3. Turn off the printer. 4. Remove the fuser. 5. Measure the resistance between fuser connectors J6007LA-2 and J6007LA-3. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. 6. Replace the DC controller PCA.
Code: 51.20
Display:
51.XX Error Turn off then on
Description:
A printer error has occurred. Laser Black
Remedy:
1. Press OK to continue. 2. If the message persists, turn the printer off and then on. 3. Reseat DC controller connectors J1010, J1012, and J1021. 4. Replace the flat cable. 5. Replace the DC controller PCA as necessary.
Code: 51.21
Display:
51.XX Error Turn off then on
Description:
A printer error has occurred. Laser Cyan
Remedy:
1. Press OK to continue. 2. If the message persists, turn the printer off and then on. 3. Reseat DC controller connectors J1010, J1012, and J1021. 4. Replace the flat cable. 5. Replace the DC controller PCA as necessary.
Code: 51.22
Display:
51.XX Error Turn off then on
Description:
A printer error has occurred. Laser Yellow
Remedy:
1. Press OK to continue. 2. If the message persists, turn the printer off and then on. 3. Reseat DC controller connectors J1010, J1012, and J1021. 4. Replace the flat cable. 5. Replace the DC controller PCA as necessary.
Code: 51.23
Display:
51.XX Error Turn off then on
Description:
A printer error has occurred. Laser Magenta
Remedy:
1. Press OK to continue. 2. If the message persists, turn the printer off and then on. 3. Reseat DC controller connectors J1010, J1012, and J1021. 4. Replace the flat cable. 5. Replace the DC controller PCA as necessary.
Code: 54.15
Display:
54.XX Error
Description:
An error has occurred with one of the tonerlevel sensors.
Yellow
Remedy:
1. Make sure that connector J1020 on the DC controller is seated correctly. 2. Replace the DC controller PCA.

Code: 54.16
Display:
54.XX Error
Description:
An error has occurred with one of the tonerlevel sensors.
Magenta
Remedy:
1. Make sure that connector J1020 on the DC controller is seated correctly. 2. Replace the DC controller PCA.
Code: 54.17
Display:
54.XX Error
Description:
An error has occurred with one of the tonerlevel sensors.
Cyan
Remedy:
1. Make sure that connector J1020 on the DC controller is seated correctly. 2. Replace the DC controller PCA.
Code: 54.18
Display:
54.XX Error
Description:
An error has occurred with one of the tonerlevel sensors.
Black
Remedy:
1. Make sure that connector J1020 on the DC controller is seated correctly. 2. Replace the DC controller PCA.
Code: 55.X
Display:
55.X Error Turn off then on
Description:
A communication error between the DC controller and the formatter has occurred.
Remedy:
1. Turn the printer off. 2. Reconnect the connector between the DC controller and the formatter. 3. Replace the DC controller PCA.
Code: 56.XX
Display:
56.XX Error
Description:
One of the trays is installed incorrectly.
Remedy:
Make sure tray 2 and optional tray 3 are completely closed.
Code: 57.XX
Display:
57.XX Error Turn off then on
Description:
A printer fan error has occurred.
Remedy:
1. Check that connector J1008 on the DC controller is seated correctly. 2. Replace the fan. 3. Replace the DC controller PCA.
Code: 59.30
Display:
59.30 Error
Description:
An error occurred with the fuser motor during startup or rotation.
Remedy:
1. Turn the printer off then on. 2. Check that connectors J5008 on the fuser motor and J213 on the driver PCA are seated correctly. 3. Replace the fuser. 4. Replace the fuser drive motor.
Code: 59.40
Display:
59.40 Error
Description:
An error occurred with the fuser motor during startup or rotation.
Remedy:
1. Turn the printer off then on. 2. Check that connectors J5008 on the fuser motor and J213 on the driver PCA are seated correctly. 3. Replace the fuser. 4. Replace the fuser drive motor.

Code: 59.50
Display:
59.50 Error
Description:
An error occurred with the black printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5006 on the black print-cartridge drive motor and J208 on the driver PCA are seated correctly. 2. Replace the black print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.51
Display:
59.51 Error
Description:
An error occurred with the cyan printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5004 on the cyan print-cartridge drive motor and J207 on the driver PCA are seated correctly. 2. Replace the cyan print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.52
Display:
59.52 Error
Description:
An error occurred with the magenta printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5003 on the magenta print-cartridge drive motor and J207 on the driver PCA are seated correctly. 2. Replace the magenta print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.53
Display:
59.53 Error
Description:
An error occurred with the yellow printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5005 on the yellow print-cartridge drive motor and J208 on the driver PCA are seated correctly. 2. Replace the yellow print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.60
Display:
59.60 Error
Description:
An error occurred with the black printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5006 on the black print-cartridge drive motor and J208 on the driver PCA are seated correctly. 2. Replace the black print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.61
Display:
59.61 Error
Description:
An error occurred with the cyan printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5004 on the cyan print-cartridge drive motor and J207 on the driver PCA are seated correctly. 2. Replace the cyan print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.62
Display:
59.62 Error
Description:
An error occurred with the magenta printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5003 on the magenta print-cartridge drive motor and J207 on the driver PCA are seated correctly. 2. Replace the magenta print-cartridge drive motor. 3. Replace the driver PCA.
Code: 59.63
Display:
59.63 Error
Description:
An error occurred with the yellow printcartridge drive motor during startup or rotation.
Remedy:
1. Check that connectors J5005 on the yellow print-cartridge drive motor and J208 on the driver PCA are seated correctly. 2. Replace the yellow print-cartridge drive motor. 3. Replace the driver PCA.


Code: 59.73
Display:
59.73 Error
Description:
An error occurred with the developer motor.
Remedy:
1. Check that connectors J403 and J405 on the driver PCA are seated correctly. 2. Check that connector J1020 on the DC controller PCA is seated correctly. 3. Check that connector J5008 on the fuser motor and J213 on the driver PCA are seated correctly. 4. Replace the developer motor solenoid (s). 5. Replace the memory tag PCA. 6. Replace the fuser.
Code: 59.83
Display:
59.83 Error
Description:
An error occurred with the developer motor.
Remedy:
1. Check that connectors J403 and J405 on the driver PCA are seated correctly. 2. Check that connector J1020 on the DC controller PCA is seated correctly. 3. Check that connector J5008 on the fuser motor and J213 on the driver PCA are seated correctly. 4. Replace the developer motor solenoid (s). 5. Replace the memory tag PCA. 6. Replace the fuser.
Code: 59.90
Display:
59.90 Error
Description:
An error occurred with the ETB motor during startup or rotation.
Remedy:
1. Check that connectors J5002 on the ETB motor and J206 on the driver PCA are seated correctly. 2. Replace the ETB. 3. Replace the driver PCA.
Code: 59.A0
Display:
59.A0 Error
Description:
An error occurred with the ETB motor during startup or rotation.
Remedy:
1. Check that connectors J5002 on the ETB motor and J206 on the driver PCA are seated correctly. 2. Replace the ETB. 3. Replace the driver PCA.
Code: 59.C0
Display:
59.C0 Error
Description:
An error occurred with the developing separation-drive assembly.
Remedy:
1. Check that the following connectors on the driver PCA are seated correctly: J403, J405, J213. 2. Check that connector J1020 on the DC controller is seated correctly. 3. Check that connector J5008 on the fuser motor is seated correctly. 4. Replace the developing separationdrive assembly. 5. Replace the fuser.
Code: 59.F0
Display:
59.F0 Error
Description:
The transfer rollers in the ETB are not engaged.
Remedy:
1. Check that the following connectors on the driver PCA are seated correctly: • J5002 on the ETB motor • J5011 on the transfer-roller separation solenoid • J206 on the driver PCA • J1019 on the DC controller 2. Replace the ETB motor. 3. Replace solenoid SL5011.
Code: 79
Display:
79 Error Turn off then on
Description:
A critical hardware error has occurred.
Remedy:
1. Turn the printer off and then on. 2. Reseat the firmware DIMM. 3. Reseat the formatter. 4. Replace the firmware DIMM. 5. Replace the formatter.
Code: 79
Display:
79 Service Error Turn off then on
Description:
The DIMM is not compatible.
Remedy:
Install a supported DIMM.

苏州hp维修站,苏州hp售后苏州维修电话

热门关注
· HP Color LaserJet 2820常见故障代码描述,英文手册
· HP Color LaserJet 2830常见故障代码描述,英文手册
· HP Color LaserJet 2840常见故障代码描述,英文手册
· HP Color LaserJet 3000常见故障代码描述,英文手册1
· HP Color LaserJet 3000常见故障代码描述,英文手册2
· HP Color LaserJet 3600常见故障代码描述,英文手册2
· HP Color LaserJet 3600常见故障代码描述,英文手册1
· HP Color LaserJet 3500常见故障代码描述,英文手册
· HP Color LaserJet 3550常见故障代码描述,英文手册
· HP Color LaserJet 3700常见故障代码描述,英文手册
· HP Color LaserJet 4500常见故障代码描述,英文手册
· HP Color LaserJet 4550常见故障代码描述,英文手册
· HP Color LaserJet 4610常见故障代码描述,英文手册
· HP Color LaserJet 4700常见故障代码描述,英文手册1
· HP Color LaserJet 4700常见故障代码描述,英文手册2
· HP Color LaserJet 4650常见故障代码描述,英文手册2
· HP Color LaserJet 4650常见故障代码描述,英文手册1
· HP Color LaserJet 3800常见故障代码描述,英文手册2
· HP Color LaserJet 3800常见故障代码描述,英文手册1
· HP Color LaserJet 4600常见故障代码描述,英文手册
· HP Color LaserJet 5500常见故障代码描述,英文手册
· HP Color LaserJet 5550常见故障代码描述,英文手册
· HP Color LaserJet 8500常见故障代码描述,英文手册1
· HP Color LaserJet 8500常见故障代码描述,英文手册2
· HP Color LaserJet 8550常见故障代码描述,英文手册2
· HP Color LaserJet 8550常见故障代码描述,英文手册1
· HP Color LaserJet 4730mfp常见故障代码描述,英文手册2
· HP Color LaserJet 4730mfp常见故障代码描述,英文手册1
· HP Color LaserJet 9500常见故障代码描述,英文手册2
· HP Color LaserJet 9500常见故障代码描述,英文手册1
推荐文章
· HP-MFPM176N加了粉还提示墨粉量低
· hp3630墨盒加墨水图解
· hp3035错误信息49.ff04
· HPLaserjet1100serues显示感叹号
· hpM176一直提示三角感叹号错误是怎么回事
· hp1112开机灯闪烁
· HP系统错误7904关闭电源如果问题仍存在,请致电HP支持中心
· hpp2055d提示49err3d910c8怎么解决
· HPM1005复印薄的文稿有黑影
· hp226dw提示扫描仪错误17关闭然后打开
· HP1280电源灯不亮的真正原因
· hpp1606n不进纸,是什么问题
· HP2025彩色打印机报错59是哪里的问题
· RicohprinterSC680
· hpm128fp开机一直显示正在初始化
· hp1319f屏幕 无显
· HP M1005一体机安装程序错误,RPC服务器不可用
· HP M1005 开机报scanner error 20错误,故障原因
· HP1020/HP1020PLUS/HP1010/HP1007定影器故障夹纸原因
· HP1008打印文稿纸中间有白道,字体模糊?
· HP1005经常夹纸,并且纸夹在定影器处
· HP1213收发不了传真问题
· HP1025彩色打印机加粉步骤
· HP5200打印白纸,无字问题原因
· HP1025机器偏色校准
· hp5200LX提示13.20.00顶盖卡纸,解决方案
· HP1536解除密码方法
· HP1536打印机打印靠右侧坚向全白,换硒鼓打印故障以旧
· HP Designjet 500 ,800系列打印机 - 打印结束后不裁纸并报错 6105
· HP T610/T1100显示要更换裁刀的处理方法
· hp500绘图仪是打印时每隔10CM就出现一次重影
· HP Designjet 500与800打印内容左右有重影
· HP Designjet 500 和 800 系列打印机 - 系统错误 6105 Processing Job
· HP Designjet 100和110系列绘图仪报错误代码0113 错误代码
· HP Designjet系列绘图仪打印线条失真如何解决
· HP Designjet系列绘图仪喷嘴堵塞如何解决
· HP Designjet T610绘图仪报系统错误 7104
· HP500/800系列绘图仪常见故障2110
· HP DJ2500报system error 020004 000000003,服务站坏
· HP2500报Incorrect ink system 不正确的供墨系统
· HP P1007 打印表格很淡,如同白纸一样
· HP1005经常夹纸,并且纸夹在定影器处,经查看定影膜上粘了好多碳粉,并且有破损
· HP1213收发不了传真,一般有以下可能
· HP5200打印白纸
· HP1025机器校准偏色方法
· HP 1020打印机开机无反应绿灯亮
· hp喷墨打印机不进纸的解决方案
· hp5200印有时会出现打印一份出好几份的情况,有时会出现连续不停的打印
· hp3800打不出 国旗红的,红色没有?
· hp7000开机后,墨盒M灯闪