电话696l6769,> 维修资料 > hp > 苏州hpHP Color LaserJet 4610售后维修电话696l6769> 苏州hp打印机维修服务网

hp Color LaserJet 4610常见故障代码描述,英文手册

更新时间:2024/10/8 12:48:15,view:144

hp打印机HPColorLaserJet4610苏州hp打印机售后服务中心客服热线69616769,苏州hp售后电话,hp售后网点,

Code: 10.10.YY
Display:
10.10.YY SUPPLY MEMORY ERROR
Description:
The printer cannot read or write to the print cartridge memory tag or the memory tag is missing. 10.10.00 black print cartridge 10.010.01 cyan print cartridge 10.10.02 magenta print cartridge 10.10.03 yellow print cartridge
Remedy:
1 Turn the printer off and then back on. 2 Exchange the cartridge for the indicated color with a cartridge in another slot to determine whether the error follows the cartridge or stays with the slot. If the error follows the cartridge, replace that cartridge. Otherwise, continue with step 3. 3 Reseat the connectors between the memory PCA (J602-J605) and the antenna PCAs (J901A-D), the memory PCA, and the DC controller PCA (J1028). 4 Replace the antenna PCA. 5 Replace the memory PCA. 6 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller
Code: 10.30.YY
Display:
10.30.YY
Description:
A non-hp print cartridge is installed. 10.30.00 black print cartridge 10.30.01 cyan print cartridge 10.30.02 magenta print cartridge 10.30.03 yellow print cartridge
Remedy:
1 Turn the printer off and then on. 2 Remove all of the print cartridges and turn the printer off and then on. 3 If the error persists, replace the indicated cartridge.
Code: 10.XX.YY
Display:
10.XX.YY SUPPLYY MEMORY ERROR
Description:
The printer cannot read or write to at least one print cartridge memory tag or at least one memory tag is missing. 10.00.00 black print cartridge 10.00.01 cyan print cartridge 10.00.02 magenta print cartridge 10.00.03 yellow print cartridge NOTE The supplies gauge shows the print cartridge consumption levels.
Remedy:
1 Turn the printer off and then back on. 2 Press ? for more information
Code: 13.02.00
Display:
13.02.00 JAM IN Tray X
Description:
A page is jammed in tray 2, tray 3, or tray 4.
Remedy:
1 Press ? for detailed information about clearing the jam. 2 Press up and down to step through the instructions. 3 Clean the pickup roller. If it is worn or damaged, replace it. 4 Clean the feed roller. If it is worn or damaged, replace it. 5 Replace the tray X pickup solenoid. 6 Replace the pickup motor. 7 Replace the paper pickup assembly (for tray 2). 8 Replace the tray X paper feeder PCA (for the 500-sheet tray 3 or the 2 x 500-sheet feeder). 9 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller
Code: 13.05.00
Display:
13.05.00 JAM IN PAPER PATH
Description:
A page has jammed in the media path.
Remedy:
1 Press for detailed information about clearing the jam. 2 Press and to step through the instructions. 3 If paper is folding into an accordion shape, check whether the shutter on each print cartridge opens as you close the ETB and each cartridge is turning correctly. Replace defective print cartridges or drive motors. 4 Clean the attaching roller at the bottom of the ETB and make sure that the spring is holding it in place. 5 If the attaching roller gears are defective, replace the ETB. Calibrate the printer after replacing the ETB. 6 Replace the paper pickup PCA. 7 Replace the ETB if it is not moving paper correctly. Calibrate the printer. 8 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 13.09.00
Display:
13.09.00 JAM IN TOP COVER AREA
Description:
A page jammed as it entered the fuser.
Remedy:
1 Press for detailed information about clearing the jam. 2 Press and to step through the instructions. 3 Check that the fuser paper sensor is in place and is functioning correctly. If it is defective, replace it. 4 Replace the fuser. WARNING! The fuser might be hot. 5 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 13.0A
Display:
13.0A JAM IN TOP COVER AREA
Description:
A jam exists in the top cover.
Remedy:
1 Press for detailed information about clearing the jam. 2 Press up and down to step through the instructions
Code: 13.12.00
Display:
13.12.00.JAM IN DUPLEX PATH
Description:
A jam exists in the duplex path.
Remedy:
1 Press ? for detailed information about clearing the jam. 2 Press up and down to step through the instructions. 3 Determine whether the ETB rollers or gears are worn or defective. Replace the ETB if they are. 4 Check the duplex feed guide, which is part of the control-panel crossmember assembly. If the guide is worn or damaged, replace the crossmember assembly.

Code: 13.20.00
Display:
13.20.00 JAM IN TOP COVER AREA
Description:
A page has jammed as it entered the fuser.
Remedy:
1 Press for detailed information about clearing the jam. 2 Press and to step through the instructions. 3 Check that the fuser paper sensor is in place. If it is defective, replace it. 4 Replace the fuser. WARNING! The fuser might be hot. 5 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 13.XX.YY
Display:
13.XX.YY.JAM IN TRAY 1
Description:
A page is jammed in the multipurpose tray.
Remedy:
1 Press ? for detailed information about clearing the jam. 2 Press up and down to step through the instructions. 3 Clean the pickup roller. If it is worn or damaged, replace it. 4 Clean or replace the separation pad. 5 Replace the tray 1 pickup solenoid. 6 Replace the tray 1 pickup motor. 7 Replace the paper pickup assembly. 8 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 20
Display:
20 INSUFFICIENT MEMORY
Description:
The printer has received more data from the computer than fits in the available memory.
Remedy:
1 Press GO to resume printing (see the note below). 2 Reduce the complexity of the print job to avoid this error. 3 Adding memory to the printer may allow printing of more complex pages. NOTE A loss of data will occur.
Code: 22
Display:
22 EIO X BUFFER OVERFLOW
Description:
The printer EIO card in slot X has overflowed its I/O buffer during a busy state.
Remedy:
Press GO to resume printing. NOTE A loss of data will occur.
Code: 22
Display:
22 PARALLEL I/O BUFFER OVERFLOW
Description:
The printer parallel buffer has overflowed during a busy state.
Remedy:
Press GO to resume printing. NOTE A loss of data will occur.
Code: 22
Display:
22 SERIAL I/O BUFFER OVERFLOW
Description:
The printer serial buffer has overflowed during a busy state.
Remedy:
Press GO to resume printing. NOTE A loss of data will occur.
Code: 40
Display:
40 BAD SERIAL TRANSMISSION
Description:
A serial data error (parity, framing:
40 BAD SERIAL TRANSMISSION
Description:
A serial data error (parity, framing, or line overrun) has occurred while the printer was receiving data.
Remedy:
Press GO to resume printing. NOTE A loss of data will occur.
Code: 40
Display:
40 EIO X BAD TRANSMISSION
Description:
A connection with the card in EIO slot X has been broken abnormally.
Remedy:
1 Press GO to resume printing (see note below). 2 Check that all cables are connected to the EIO ports and that the EIO board is seated properly. 3 If possible, print to another network printer to verify the network is working properly. NOTE A loss of data will occur.

Code: 41.3
Display:
41.3 UNEXPECTED SIZE IN TRAY XX
Description:
The media that is loaded is longer or shorter in the feed direction than the size that is configured for the tray.
Remedy:
1 If the incorrect size was selected, cancel the job or press for more information. 2 Press up and down to step through the instructions.
Code: 41.5
Display:
41.5 UNEXPECTED TYPE IN TRAY X
Description:
The printer senses a different media type in the media path than the type that is configured in the tray.
Remedy:
If the incorrect type was selected, cancel the job or press ? for more information. 2 Press up and down to step through the instructions.
Code: 41.X
Display:
41.X PRINTER ERROR
Description:
A printer error has occurred. X Description 1 unknown misprint error 2 beam detect misprint error 3 media feed error (size) no VSYNC error 5 media feed error (type) 6 ETB detection error 7 feed delay error 9 noise VSREQ
Remedy:
1 Press GO to continue or press ? for more information. 2 If the message persists, turn the printer off and then on.rror
Code: 49.XXXX
Display:
49.XXXX PRINTER ERROR
Description:
A critical firmware error has occurred that caused the processor on the formatter to abort operation. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. In some cases, electrical noise in the cable can corrupt data during transmission to the printer. Other causes include poorquality parallel cables, poorconnections, or home-grown programs. On rare occasions, the formatter is at fault, which is usually indicated by a 79 Service Error.
Remedy:
1 Press CANCEL JOB to clear the print job from the printer memory. 2 Turn the printer off and then on. 3 Try printing a job from a different software program. If the job prints, go back to the first program and try printing a different file. If the message appears only with a certain software program or print job, contact the software vendor for assistance. 4 If the message persists with different software programs and print jobs, disconnect all of the cables to the printer that connect it to the network or computer. 5 Turn the printer off. 6 Remove all memory DIMMs or third-party DIMMs from the printer. 7 Remove all EIO devices from the printer. 8 Turn the printer on. 9 If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and on again as you install each device. 10 Replace a DIMM or EIO device if you determine that it causes the error. 11 Remember to reconnect all of the cables that connect the printer to the network or computer. 12 If the error persists, replace the firmware DIMM. 13 Replace the formatter and calibrate the printer.
Code: 50.X
Display:
50.X FUSER ERROR
Description:
A fuser error has occurred.
X Description: 1 low fuser temperature o 2 fuser warmup service 3 high fuser temperature 4 faulty fuser 5 inconsistent fuser 6 open fuser 7 fuser pressure-release mechanism failure
Remedy:
1 Turn the printer off and allow it to cool down. 2 Reinstall the fuser, and check the connector J4034 that connects the fuser and the printer. Replace the connector if it is damaged. 3 Turn the printer off and remove the fuser. Measure the resistance between the connector pins on the fuser. If resistance does not meet the following guidelines, replace the fuser. • J4034-5 to J4034-6: 300 - 500 KOhms • J4034-1 to J4034-2: less than 1 KOhm 4 Check for continuity between connector pins J4034-4 and J4034-2. If no continuity exists, replace the fuser. 5 Replace the fuser power supply PCA. 6 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 51.XY
Display:
51.XY PRINTER ERROR
Description:
A printer error has occurred.
X Description: 1 beam detect error 2 laser error Y Description 0 no color/black 1 cyan 2 magenta 3 yellow
Remedy:
1 Press to continue. 2 Turn the printer off and then on. 3 Reseat the connectors between the laser/ scanner and DC controller PCA (J1009 - J1012). 4 Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner. 5 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 52.XY
Display:
52.XY PRINTER ERROR
Description:
A printer error has occurred.
X Description: 1 scanner error 2 scanner startup error 3 scanner rotation error
Y Description: 0 no color/black 1 cyan 2 magenta 3 yellow
Remedy:
1 Press to continue. 2 Turn the printer off and then on. 3 Reseat the connectors between the laser/ scanner and DC controller PCA (J1009 - J1012). 4 Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner. 5 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 53.XY.ZZ
Display:
53.XY.ZZ CHECK RAM DIMM SLOT
Description:
An error occurred in some printer memory.
X DIMM Type: 1 Slot 1 2 Slot 2
Y Device Location: 1 DDR Slot 1 2 DDR Slot 2
ZZ Error Number: 0 unsupported memory 1 unrecognized memory 2 unsupported memory size 3 failed RAM test 4 exceeded maximum RAM size 5 invalid DDR speed
Remedy:
NOTE The hp Color LaserJet 4610n printer has only one DIMM slot. 1 Turn the printer off. 2 Verify that the memory meets specifications and is correctly installed. 3 Turn the printer on. 4 If the problem persists, replace the DDR card in the slot indicated.

Code: 54.20.00
Display:
54.20.00 PRINTER ERROR
Description:
Printing cannot continue. The CPR sensor out of range.
Remedy:
1 For step-by-step information, press GO. 2 Turn the printer off and then on.
Code: 54.X
Display:
54.X PRINTER ERROR
Description:
X Description: 1 low fuser temperature 3 Dmax density sensor 5 CPR sensor 6 OHT sensor 7 yellow drum phase (home) position sensor 8 magenta drum phase (home) position sensor 9 cyan drum phase (home) position sensor 10 black drum phase (home) position sensor 11 yellow density sensor 12 magenta density sensor 13 cyan density sensor 14 black density sensor 15 yellow CPR sensor 16 magenta CPR sensor 17 cyan CPR sensor 18 black CPR sensor 19 ETB speed control sensor 20 color-plane-registration sensor 21 black toner-level sensor 1E or 30 halftone calibration error 01 humidity environmental sensor abnormal
Remedy:
Turn the printer off and then on, and then check the following items in the order listed. 54.1 error: Check the fuser. See 50.X fuser error. 54.3 error: Check the connections. Replace the color registration detection assembly. 54.5 error: Check the connections. Replace the color registration detection assembly. 54.6 error: Check the connections. Replace the paper pickup unit. 54.7, 54.8, 54.9, or 54.10 error: Check the connections. Replace the drum-phase sensor for the indicated color. 54.11, 54.12, 54.13, or 54.14 error: Check the connections. Check the cartridge and replace it if necessary. Replace the color-registration detection assembly. 54.15, 54.16, 54.17, 54.18: Check the connections. Replace the color registration detection assembly. 54.19 error: Check the ETB connection. Replace the ETB. Replace the DC controller. Calibrate the printer. 54.20 error: Check the connection. Replace the color-registration detection assembly. 54.21, 54.22, 54.23, or 54.24 error: Check the connections. Replace the toner-level sensing PCA. Replace the DC controller. Calibrate the printer.
Code: 54.XX.00
Display:
54.XX.00 PRINTER ERROR
Description:
Printing cannot continue. The CPR sensor out of range. X values 15 = yellow 16 = magenta 17 = cyan 18 = black
Remedy:
1 For step-by-step information, press GO. 2 Turn the printer off and then on.
Code: 55.01.XY
Display:
55.01.XY DC CONTROLLER ERROR
Description:
The DC controller is not communicating with the formatter. The problem could be caused by a timing error or an intermittent connection.
X Description: 0 communication error 1 DC controller memory error 2 outgoing party error 3 no engine response 4 communication timeout
Remedy:
1 Press GO to continue. 2 Turn the printer off and then on. 3 Reseat or replace the connectors between the DC controller and the formatter. 4 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller. 5 Replace the formatter. Initialize NVRAM.
Code: 56.XX
Display:
56.XX PRINTER ERROR
Description:
A printer error has occurred.
XX Description: 01 illegal input 02 illegal output
Remedy:
Turn the printer off then on again. If the error persists, record the message and call support.
Code: 57.X
Display:
57.X PRINTER ERROR
Description:
A printer-fan error has occurred.
X Description: 3 cartridge fan (vertical fan, F2) 4 formatter fan (horizontal fan, F1) 7 power supply fan (F3; hp Color LaserJet 4650 models)
Remedy:
Turn the printer off and then on. 57.3 Cartridge fan error (F2) 1 Reconnect the connector J1004 on the DC controller PCA. 2 Immediately after starting the print operation, measure the voltage between pins 1 and 3 on the J1004 connector. If the voltage changes from 0 V to 24 V, replace the cartridge fan. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller 57.4 Formatter fan error (F1) 1 Reconnect the connector J1003 on the DC controller PCA. 2 Immediately after turning the printer on, measure the voltage between pins 1 and 3 on the J1004 connector. If the voltage changes from 0 V to 24 V, replace the formatter fan. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller. 57.5 Power-supply fan error (F3) (hp Color LaserJet 4650 models) 1 Reconnect the connector J1037 on the DC controller PCA. 2 Immediately after turning the printer on, measure the voltage between pins 1 and 3 on the J1037 connector. If the voltage changes from 0 V to 24 V, replace the powersupply fan. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.
Code: 58.X
Display:
58.X PRINTER ERROR
Description:
A memory tag error was detected.
X Description: 2 air-temperature sensor 3 CPU 4 power supply
Remedy:
1 Turn the printer off and then on. 2 Replace the memory PCA. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller
Code: 59.XY
Display:
59.XY PRINTER ERROR
Description:
A printer motor error has occurred.
X Description: 0 motor error 1 motor startup error 2 motor rotation error 3 fuser motor startup error 4 fuser motor rotation error 5 print cartridge motor startup error 6 print cartridge motor rotation error 9 ETB motor startup error A ETB motor rotation error B developing disengaging motor startup error C developing disengaging motor rotation error
Y Description: 0 no color/black 1 cyan 2 magenta 3 yellow
Remedy:
1 Turn the printer off and then on. 2 This message might also appear if the transfer unit is missing or incorrectly installed. Ensure that the transfer unit is correctly installed. ETB motor error 1 Clean the ETB unit intermediate connector, J4017. . 2 Reconnect the connectors J4022 for the ETB motor, J4017 between the ETB and the printer, and J4014 on the DC controller PCA. 3 Replace the ETB motor. 4 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller. Fuser motor error 1 Reconnect the connectors J4030 for the fuser motor and J1002 on the DC controller PCA. 2 Replace the fuser drive assembly. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller. Print cartridge motor error 1 Reconnect the print cartridge connector on the DC controller PCA (J1013 for cyan, J1031 for magenta, J1032 for yellow, and J1033 for black). 2 Replace the drum drive assembly for the indicated print cartridge. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller. Developing-disengaging motor error 1 Reconnect the connectors J4024 and J1019 between the developing-disengaging motor and the DC controller PCA. 2 Replace the developingdisengaging drive assembly. 3 Replace the DC controller PCA. Calibrate the printer after replacing the DC controller.

Code: 62
Display:
62 NO SYSTEM
Description:
No system was found.
Remedy:
1 Turn the printer off and then on. 2 Reseat the firmware DIMM.
Code: 68.X
Display:
68.X STORAGE ERROR SETTING CHANGE
Description:
One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to its factory default. Pressing GO should clear the message. Printing can continue, but unexpected behavior might occur.
X Description: 0 on board NVRAM 1 removable disk (flash or hard)
Remedy:
1 Press GO to continue. 2 Turn the printer off and then back on. 3 Check the printer settings to determine which settings have been changed.
Code: 68.X
Display:
68.X PERMANENT STORAGE FULL
Description:
A non-volatile storage device is full. Pressing GO should clear the message. Printing can continue, but unexpected behavior might occur.
X Description: 0 on board NVRAM 1 removable disk (flash or hard)
Remedy:
1 Press GO to continue. 2 For 68.0 errors, turn the printer off and then on. 3 If a 68.0 error persists, perform an NVRAM inititialization. 4 For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive. 5 If a 68.1 errors persists, reinitialize the hard disk. NOTE The removable hard disk is not available for the hp Color LaserJet 4610n printer.
Code: 68.X
Display:
68.X PERMANENT STORAGE WRITE FAIL
Description:
A non-volatile storage device is failing to write. Pressing should clear the message. Printing can continue, but unexpected behavior might occur.
X Description: 0 on board NVRAM 1 removable disk (flash or hard)
Remedy:
1 Press GO to continue. 2 Turn the printer off and then on. 3 If the problem persists, initialize NVRAM. 4 Reinitialize the hard disk.
Code: 79.XXXX
Display:
79.XXXX PRINTER ERROR
Description:
A critical hardware error has occurred.
Remedy:
1 Turn the printer off and then on. 2 If the problem persists, reseat the firmware DIMM. 3 Reseat the formatter. 4 Replace the firmware DIMM. 5 Replace the formatter. Calibrate the printer.
Code: 8X.YYYY
Display:
8X.YYYY EIO ERROR
Description:
The EIO accessory card in slot X has encountered a critical error. 81 EIO ERROR = error in slot 1 82 EIO ERROR = error in slot 2
Remedy:
1 Turn the printer off and then on. 2 If the problem persists, reseat the EIO card. 3 Replace the EIO card.

热门图文

相关资料补充_苏州hp维修点售后电话_HPColorLaserJet4610维修手册_错误代码0512-69616769 更新日期2024/9/20 4:04:14

»hpC7280一体机,现在是连供的墨盒,打印机清零后,能用几天。打印还很清晰。就是老出现墨水系统故障,不能打印复印。连供墨盒只安装了黑色墨盒芯片,彩色没有安装芯片。请问修过这样的机器吗? 1258

»hpcp352559.f0代码时好时坏 56

»hpCM6040提示热凝器错误50.1 72

»HPCP2025多张打印过程中提示cleaning红绿灯闪烁,屏幕提示MisprintpressOK,必 93

»HPCP1525N打印两三页后机器就出现“MisprintpressOk”的提示 55

»hpcp522510.9531错误什么问题 338

»hpcp5525故障代码59.00.f0 197

»HPCP1025三角感叹号黄灯闪是什么意思 97

»HPcp1025提示热凝器错误原因 775

»hpcp4025故障代码50.f0 83

»HPCP1025彩色喷墨打印机有点小问题这个鼓是不是用久了打出来的图片颜色就比较淡 1116

»hpcp1025被识别为移动存储 58

»HPCP4525提示转印套件不足怎样清除? 148

»HPCP5225n报错:59.F0 84

»HPCP2025打印几张就提示:CleaningMisPrintPressOK 4513


hp打印机HPColorLaserJet4610苏州姑苏区hp售后服务电话0512-696l6769,苏州hpHPColorLaserJet4610售后电话,hpHPColorLaserJet4610姑苏区售后网点,hpHPColorLaserJet4610维修手册,hpHPColorLaserJet4610驱动程序下载,hpHPColorLaserJet4610打印机售后维修点,hpHPColorLaserJet4610厂家电话,故障代码在线技术交流,有问必答,hpHPColorLaserJet4610卡纸,打印浅,亮红灯,不通电,无法使用等故障自己查询维修资料即可解决问题


热门关注
· hp color laserjet 4700常见故障代码描述,英文手册1

· hp color laserjet 4700常见故障代码描述,英文手册2

· hp color laserjet 4650常见故障代码描述,英文手册2

· hp color laserjet 4650常见故障代码描述,英文手册1

· hp color laserjet 3800常见故障代码描述,英文手册2

· hp color laserjet 3800常见故障代码描述,英文手册1

· hp color laserjet 4600常见故障代码描述,英文手册

· hp color laserjet 5500常见故障代码描述,英文手册

· hp color laserjet 5550常见故障代码描述,英文手册

· hp color laserjet 8500常见故障代码描述,英文手册1

· hp color laserjet 8500常见故障代码描述,英文手册2

· hp color laserjet 8550常见故障代码描述,英文手册2

· hp color laserjet 8550常见故障代码描述,英文手册1

· hp color laserjet 4730mfp常见故障代码描述,英文手册2

· hp color laserjet 4730mfp常见故障代码描述,英文手册1

· hp color laserjet 9500常见故障代码描述,英文手册2

· hp color laserjet 9500常见故障代码描述,英文手册1

· hp color laserjet cm2320常见故障代码描述,英文手册

· hp color laserjet cm1415常见故障代码描述,英文手册

· hp color laserjet cm1410常见故障代码描述,英文手册

· hp color laserjet cm1017常见故障代码描述,英文手册

· hp color laserjet cm1015常见故障代码描述,英文手册

· hp color laserjet cm1312常见故障代码描述,英文手册

· hp color laserjet cm4540常见故障代码描述,英文手册4

· hp color laserjet cm4540常见故障代码描述,英文手册3

· hp color laserjet cm4540常见故障代码描述,英文手册2

· hp color laserjet cm4540常见故障代码描述,英文手册1

· hp color laserjet cm3530常见故障代码描述,英文手册1

· hp color laserjet cm3530常见故障代码描述,英文手册2

· hp color laserjet cm4730常见故障代码描述,英文手册2

推荐文章
· hp打印机不认墨盒

· hp5500绘图仪,打印机打印时出现0c00400000020c

· hp5200n打印机打印一个东西显示什么服务请求已接受

· hp5225怎么恢复出厂

· hplaserjetpro400mfp打印时显示50.2定音影器错误,是怎么回事?

· hp3015 报错50.10 怎么回事?

· hpj4580显示托架被卡住,打开打印托架检修门,清除卡塞?是哪出问题求大神指教

· hp1025 报错硒鼓错误.

· hpc7280开机老提示后面卡纸,但无纸,谁碰到过,怎么处理

· hp4525定影器和转印组件提示寿命到了,谁知道怎么清掉

· hpcp1025提示热凝器错误原因

· hp 提示59.c0错误

· hpcp1025打印一半清楚一半不清楚

· hp1215打印机显示青色碳粉盒内存错误是什么意思?

· hp3055打印机报scannererror3错误是什么问题

· hp3600齿轮组对位调整方法

· hp1108打印机上有个感叹号的灯显示红色,不打印是怎么回事?

· hp1106打印机感叹号灯一直闪,是什么故障

· hp1025彩色打印机显示有错误三角形里一个感叹号

· hp1025彩色激光打印机出现三角形灯一直亮,是什么故障

· hp5025报52.20代码错误

· hp1020打印一张时,后面跟了一张空白纸、卡纸等故障

· hp1025报错三角叹号和半圆灯同时亮问题

· hp5200l提示代码57.03错误

· hp2055d机换了定影膜之后开机自检过不去

· hp1108检测不到硒鼓,是怎么回事

· hp3050一体机,打印时总提示是50fusererror,是怎么回事

· hp2055d的维修手册

· hporder-a-cartridge按错键,打印机没反映了,有很多英文字母,不知道是怎么回事

· hp1010照片打印机打出的照片发黄,缺红色为什么?

· hp1536一体打印机总是出现在复印的时候出现(初始化)是怎么回事

· hpp1106开机后绿灯黄灯常亮,不能打印是什么故障。

· hp1106开机报警灯长亮(红灯)

· hp1106新机开机红黄灯常亮自检不了

· hp3600显示10.92.00墨盒未齿合

· hp1536复印时提示49错误,是什么原因

· hpm1216扫描到出现videoinitializeerror

· hp8600喷墨打印机一直亮ky电源灯一直闪墨水系统故障我把外置每墨盒都拿掉了

· hp2025打印几张就显示清洁怎么回事

· hp3525显示错误代码59.fo是什么意思

· hp3052机开机显示scannerbuibwarmingup扫描架不动,扫描灯常亮。

· hplaserjetm1216nfhmfp中间黄灯亮,感叹灯亮红灯

· hp9050显示57.03代码,是什么原因

· hp4350n打印机显示49.4c02错误,是什么原因

· hp2055d开机显示installblackcartridge

· hp3505提示59.co错误,什么原因

· hp5100加粉后提示installtonercartridge

· hp7610打印机要不要清零

· hpz2100开机初始化的时候报错79:04

· hp1106开机预热完两个个灯长亮